Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for Hatchback with VSC)

DTC    B1870/66    Short in Driver Side Front Seat Cushion Squib Circuit

DTC    B1871/66    Open in Driver Side Front Seat Cushion Squib Circuit

DTC    B1872/66    Short to GND in Driver Side Front Seat Cushion Squib Circuit

DTC    B1873/66    Short to B+ in Driver Side Front Seat Cushion Squib Circuit

for Preparation Click here


DESCRIPTION

The seat cushion squib LH circuit consists of the airbag sensor assembly and SRS seat cushion airbag assembly LH.
The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the seat cushion squib LH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1870/66
  1. The airbag sensor assembly receives a line short circuit signal in the seat cushion squib LH circuit during primary check.
  2. Seat cushion squib LH malfunction
  3. Airbag sensor assembly malfunction
  1. Floor wire
  2. SRS seat cushion airbag assembly LH (Seat cushion squib LH)
  3. Airbag sensor assembly
B1871/66
  1. The airbag sensor assembly receives an open circuit signal in the seat cushion squib LH circuit.
  2. Seat cushion squib LH malfunction
  3. Airbag sensor assembly malfunction
B1872/66
  1. The airbag sensor assembly receives a short circuit to ground signal in the seat cushion squib LH circuit.
  2. Seat cushion squib LH malfunction
  3. Airbag sensor assembly malfunction
B1873/66
  1. The airbag sensor assembly receives a short circuit to B+ signal in the seat cushion squib LH circuit.
  2. Seat cushion squib LH malfunction
  3. Airbag sensor assembly malfunction

WIRING DIAGRAM


C222225E33


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the Techstream (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK CONNECTORS


    C167985E10
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the SRS seat cushion airbag assembly LH and airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the SRS seat cushion airbag assembly LH and airbag sensor assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.

    Text in Illustration 
    *1
    SRS Seat Cushion Airbag Assembly LH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire



NG
REPLACE FLOOR WIRE
OK


2.CHECK SRS SEAT CUSHION AIRBAG ASSEMBLY LH (SEAT CUSHION SQUIB)
SST
09843-18061  


    C245456E01
  1. Connect the connector to the airbag sensor assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the SRS seat cushion airbag assembly LH (seat cushion squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1870/66, B1871/66, B1872/66 or B1873/66 is not output.

    HINT:
    Codes other than DTCs B1870/66, B1871/66, B1872/66 and B1873/66 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    SRS Seat Cushion Airbag Assembly LH
    *2
    Airbag Sensor Assembly
    *3
    Connector C
    *a
    Front view of wire harness connector
    (to SRS Seat Cushion Airbag Assembly LH)

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Disconnect SST from connector C.



NG
Go to step 3
OK

REPLACE SRS SEAT CUSHION AIRBAG ASSEMBLY LH (Click here)  

3.CHECK FLOOR WIRE (SEAT CUSHION SQUIB LH CIRCUIT)


    C245457E01
  1. Disconnect the floor wire from the airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      J88-1 (FCD-) - Body ground
      Ignition switch ON
      Below 1 V
      J88-2 (FCD+) - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J88-1 (FCD-) - J88-2 (FCD+)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J88-1 (FCD-) - Body ground
      Always
      1 MΩ or higher
      J88-2 (FCD+) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J88-1 (FCD-) - J88-2 (FCD+)
      Always
      1 MΩ or higher

      Text in Illustration 
      *1
      SRS Seat Cushion Airbag Assembly LH
      *2
      Airbag Sensor Assembly
      *3
      Floor Wire
      *4
      Connector C
      *a
      Front view of wire harness connector
      (to SRS Seat Cushion Airbag Assembly LH)

  1. Restore the released activation prevention mechanism of connector B to the original condition.



NG
REPLACE FLOOR WIRE
OK


4.CHECK DTC


    C189113E02
  1. Connect the connectors to the SRS seat cushion airbag assembly LH and airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1870/66, B1871/66, B1872/66 or B1873/66 is not output.

    Text in Illustration 
    *1
    SRS Seat Cushion Airbag Assembly LH
    *2
    Airbag Sensor Assembly

    HINT:
    Codes other than DTCs B1870/66, B1871/66, B1872/66 and B1873/66 may be output at this time, but they are not related to this check.



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)