DTC B1697/82 Lost Communication with Door Side Airbag Sensor LH |
DTC B1698/82 Door Side Airbag Sensor LH Initialization Incomplete |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1697/82 B1698/82 | When one of following conditions is met:
|
|

| 1.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor assembly LH.
Disconnect the connectors from the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor assembly LH.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 2.CHECK FLOOR WIRE AND FRONT DOOR WIRE LH (OPEN) |
Using the service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

| *1 | Door Side Airbag Sensor LH | *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH | *4 | Floor Wire |
| *5 | Connector B | *6 | Connector E |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly LH) | *b | Front view of wire harness connector (to Door Side Airbag Sensor LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J75-1 (BDL+) - J75-2 (BDL-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE AND FRONT DOOR WIRE LH (SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J75-1 (BDL+) - J75-2 (BDL-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE AND FRONT DOOR WIRE LH (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J75-1 (BDL+) - Body ground | Ignition switch ON | Below 1 V |
| J75-2 (BDL-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE AND FRONT DOOR WIRE LH (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J75-1 (BDL+) - Body ground | Always | 1 MΩ or higher |
| J75-2 (BDL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 6.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Connect the connectors to the door side airbag sensor LH and airbag sensor assembly.
Interchange the No. 2 side airbag sensor assembly LH with the No. 2 side airbag sensor assembly RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1692/81 or B1693/81 is output. | A |
| DTC B1697/82 or B1698/82 is output. (for 5 Door) | B |
| DTC B1697/82 or B1698/82 is output. (for 3 Door) | C |
| DTC 1692/81, B1693/81, B1697/82 and B1698/82 are not output. | D |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly LH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
|
| ||||
| A | |
| 7.CHECK DOOR SIDE AIRBAG SENSOR LH |
![]() |
Interchange the door side airbag sensor LH with the door side airbag sensor RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC 1692/81, B1693/81, B1697/82 and B1698/82 are not output. | A |
| DTC B1697/82 or B1698/82 is output. | B |
| DTC B1692/81 or B1693/81 is output. | C |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the door side airbag sensor LH and the door side airbag sensor RH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | ||
| ||
| 8.CHECK FRONT DOOR WIRE LH (OPEN) |
Disconnect the floor wire connector from the front door wire LH.

| *1 | Door Side Airbag Sensor LH | *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH | *4 | Floor Wire |
| *5 | Connector D | *6 | Connector E |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector (to Floor Wire) | *b | Front view of wire harness connector (to Door Side Airbag Sensor LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| GJ1-1 (BDL+) - GJ1-2 (BDL-) | Always | Below 1 Ω |
Disconnect the service wire from the connector E.
|
| ||||
| OK | ||
| ||
| 9.CHECK FRONT DOOR WIRE LH (SHORT) |
![]() |
Disconnect the floor wire connector from the front door wire LH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| GJ1-1 (BDL+) - GJ1-2 (BDL-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector (to Floor Wire) |
|
| ||||
| OK | ||
| ||
| 10.CHECK FRONT DOOR WIRE LH (SHORT TO B+) |
Turn the ignition switch off.
![]() |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the front door wire connector from the floor wire.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| GJ1-1 (BDL+) - Body ground | Ignition switch ON | Below 1 V |
| GJ1-2 (BDL-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector (to Floor Wire) |
|
| ||||
| OK | ||
| ||
| 11.CHECK FRONT DOOR WIRE LH (SHORT TO GROUND) |
![]() |
Disconnect the front door wire connector from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| GJ1-1 (BDL+) - Body ground | Always | 1 MΩ or higher |
| GJ1-2 (BDL-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector (to Floor Wire) |
|
| ||||
| OK | ||
| ||