LIGHTING SYSTEM (for Sedan) > Door Courtesy Switch Circuit |

| 1.READ VALUE USING TECHSTREAM |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Main Body / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Door Courtesy SW | Driver side door courtesy light switch signal/ ON or OFF | ON: Driver side door is open OFF: Driver side door is closed | - |
| P Door Courtesy SW | Passenger side door courtesy light switch signal/ ON or OFF | ON: Passenger side door is open OFF: Passenger side door is closed | - |
| RR Door Courtesy SW | Rear door LH and RH courtesy light switch signal/ ON or OFF | ON: Rear door LH or RH is open OFF: Rear door LH and RH is closed | - |
| RL Door Courtesy SW | Rear door LH and RH courtesy light switch signal/ ON or OFF | ON: Rear door LH or RH is open OFF: Rear door LH and RH is closed | - |
| Luggage Door Courtesy SW | Luggage compartment courtesy switch signal/ ON or OFF | ON: Luggage door is open OFF: Luggage door is closed | - |
| Result | Proceed to |
| OK | A |
| NG (Front door courtesy light switch assembly does not operate) | B |
| NG (Rear door courtesy light switch assembly does not operate) | C |
| NG (Luggage compartment door courtesy switch) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY |
Inspect the front door courtesy light switch assembly (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY - MAIN BODY ECU) |
Disconnect J2 or J1 front door courtesy light switch assembly connector.
Disconnect the 4A main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J2-1 - 4A-21 | Always | Below 1 Ω |
| J2-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| J1-1 - 4A-24 | Always | Below 1 Ω |
| J1-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 4.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY |
Inspect the rear door courtesy light switch assembly (Click here).
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY - MAIN BODY ECU) |
Disconnect J33 or J32 rear door courtesy light switch assembly connector.
Disconnect the 4A main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J33-1 - 4A-5 | Always | Below 1 Ω |
| J33-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| J32-1 - 4A-20 | Always | Below 1 Ω |
| J32-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY (LUGGAGE COMPARTMENT DOOR COURTESY SWITCH) |
Inspect the luggage compartment door lock assembly (luggage compartment door courtesy switch) (Click here).
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - MAIN BODY ECU AND BODY GROUND) |
Disconnect the J42 luggage compartment door lock assembly (luggage compartment door courtesy switch) connector.
Disconnect the 4A main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J42-3 - 4A-7 | Always | Below 1 Ω |
| J42-3 - Body ground | Always | 10 kΩ or higher |
| J42-2 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||