Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.08–2016.04
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  B1802/51  Short to GND in Driver Side Squib Circuit  B1803/51  Short to B+ in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the airbag ECU assembly, spiral cable sub-assembly and horn button assembly.

The circuit instructs SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1800/51 Short in Driver Side Squib Circuit
·

The airbag ECU assembly receives a line short circuit signal in the driver side squib circuit during primary check.

·

Driver side squib malfunction

·

Spiral cable sub-assembly malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Horn button assembly (Driver side squib)

·

Airbag ECU assembly


DTC corresponds to check mode.
B1801/51 Open in Driver Side Squib Circuit
·

The airbag ECU assembly receives an open circuit signal in the driver side squib circuit.

·

Driver side squib malfunction

·

Spiral cable sub-assembly malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Horn button assembly (Driver side squib)

·

Airbag ECU assembly


DTC corresponds to check mode.
B1802/51 Short to GND in Driver Side Squib Circuit
·

The airbag ECU assembly receives a short circuit to ground signal in the driver side squib circuit.

·

Driver side squib malfunction

·

Spiral cable sub-assembly malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Horn button assembly (Driver side squib)

·

Airbag ECU assembly


DTC corresponds to check mode.
B1803/51 Short to B+ in Driver Side Squib Circuit
·

The airbag ECU assembly receives a short circuit to B+ signal in the driver side squib circuit.

·

Driver side squib malfunction

·

Spiral cable sub-assembly malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Horn button assembly (Driver side squib)

·

Airbag ECU assembly


DTC corresponds to check mode.

WIRING DIAGRAM

C241678E11
4.74,4.698 5.104,4.854 0.365,0.156 10 false F21 4.74,4.865 6.771,5.24 2.031,0.375 10 false Airbag ECU Assembly 2.781,3.563 3.052,3.719 0.271,0.156 10 false F9 4.792,2.219 5.083,2.375 0.292,0.156 10 false D+ 4.792,3.063 5.042,3.219 0.25,0.156 10 false D- 2.479,2.115 2.583,2.271 0.104,0.156 10 false 2 2.479,2.958 2.583,3.115 0.104,0.156 10 false 1 4.573,2.958 4.677,3.115 0.104,0.156 10 false 6 4.573,2.115 4.677,2.271 0.104,0.156 10 false 5 2.781,3.729 3.698,4.188 0.917,0.458 10 false Spiral Cable Sub-assembly 0.76,3.76 2.188,4.385 1.427,0.625 10 false Horn Button Assembly (Driver Side Squib) 0.76,3.583 0.927,3.74 0.167,0.156 10 false z3 3.594,2.969 3.698,3.125 0.104,0.156 10 false 2 3.583,2.115 3.688,2.271 0.104,0.156 10 false 1 3.313,2.115 3.583,2.292 0.271,0.177 10 false D+ 3.333,2.958 3.604,3.146 0.271,0.188 10 false D-

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C281399C01
0.146,1.448 0.25,0.958 false 1.99,1.396 1.958,0.958 false 0.396,0.802 0.552,1.021 0.156,0.219 10 false F 1.063,0.813 1.375,0.969 0.313,0.156 10 false *2 2.74,0.958 3.052,1.115 0.313,0.156 10 false *3 1.917,1.438 2.125,1.646 0.208,0.208 10 false *4 0.417,2.156 0.729,2.313 0.313,0.156 10 false *1 0.646,0.802 0.802,1.021 0.156,0.219 10 false E 1.5,0.813 1.656,1.031 0.156,0.219 10 false D 1.76,0.813 1.917,1.031 0.156,0.219 10 false C 2.104,0.813 2.26,1.031 0.156,0.219 10 false B 2.365,0.813 2.521,1.031 0.156,0.219 10 false A 0.094,1.479 0.406,1.677 0.313,0.198 10 false *1
*1 Driver Side Squib
*2 Spiral Cable Sub-Assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the spiral cable sub-assembly connector (on the steering pad side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs for the instrument panel wire and spiral cable sub-assembly with the activation prevention mechanism are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB)

NG

REPLACE WIRE HARNESS

2.CHECK HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB)
SST
09843-18061  

a.
C281400C01
0.385,2.229 0.729,2.438 0.344,0.208 0.292,1.083 0.292,0.677 false 1.75,2.281 2.031,2.073 false 0.24,1.104 0.552,1.26 0.313,0.156 10 false *1 1.156,0.531 1.469,0.688 0.313,0.156 10 false *2 2.708,0.708 3.021,0.865 0.313,0.156 10 false *3 2.323,0.542 2.635,0.698 0.313,0.156 10 false A 0.333,1.688 0.646,1.844 0.313,0.156 10 false *a 0.438,0.542 0.604,0.76 0.167,0.219 10 false F 0.75,0.542 0.917,0.76 0.167,0.219 10 false E 1.594,0.542 1.76,0.76 0.167,0.219 10 false D 1.75,0.542 1.917,0.76 0.167,0.219 10 false C 2.177,0.542 2.333,0.74 0.156,0.198 10 false B 2.042,1.99 2.5,2.188 0.458,0.198 10 false SST 0.49,2.26 0.802,2.458 0.313,0.198 10 false z3
*1 Driver Side Squib
*2 Spiral Cable Sub-Assembly
*3 Airbag ECU Assembly
*a Front view of wire harness connector
(to Horn Button Assembly (Driver Side Squib))


Connect the instrument panel wire to the airbag ECU assembly and spiral cable sub-assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect the tester to the horn button assembly (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

REPLACE HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB)

NG

3.CHECK DRIVER SIDE SQUIB CIRCUIT
3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.
C281422C01
0.531,2.25 0.823,2.448 0.292,0.198 0.281,1.156 0.333,0.688 false 2.51,0.542 2.667,0.74 0.156,0.198 10 false A 2.208,0.542 2.365,0.74 0.156,0.198 10 false B 1.75,0.542 1.906,0.74 0.156,0.198 10 false C 1.594,0.542 1.75,0.74 0.156,0.198 10 false D 0.771,0.542 0.927,0.74 0.156,0.198 10 false E 0.448,0.542 0.604,0.74 0.156,0.198 10 false F 0.198,1.177 0.51,1.375 0.313,0.198 10 false *1 1.156,0.563 1.469,0.76 0.313,0.198 10 false *2 2.865,0.698 3.177,0.896 0.313,0.198 10 false *3 0.25,1.635 0.563,1.833 0.313,0.198 10 false *a 0.604,2.26 0.917,2.458 0.313,0.198 10 false z3
*1 Driver Side Squib
*2 Spiral Cable Sub-Assembly
*3 Airbag ECU Assembly
*a Front view of wire harness connector
(to Horn Button Assembly (Driver Side Squib))


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect SST from connector E.


d.

Disconnect the instrument panel wire from the airbag ECU assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z3-2 - Body ground Ignition switch ON Below 1 V
z3-1 - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-2 - z3-1 Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-2 - Body ground Always 1 MΩ or higher
z3-1 - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-2 - z3-1 Always 1 MΩ or higher




i.

Restore the released activation prevention mechanism of connector B to the original condition.


Result:
Proceed to
OK
NG



OK

4.CHECK AIRBAG ECU ASSEMBLY

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK AIRBAG ECU ASSEMBLY
a.
C281402C01
0.375,1.344 0.396,0.885 false 0.292,1.375 0.604,1.531 0.313,0.156 10 false *1 1.104,0.719 1.417,0.875 0.313,0.156 10 false *2 0.552,0.74 0.719,0.969 0.167,0.229 10 false F 0.708,0.74 0.875,0.969 0.167,0.229 10 false E 1.542,0.74 1.708,0.969 0.167,0.229 10 false D 1.698,0.74 1.865,0.969 0.167,0.229 10 false C 2.302,0.74 2.458,0.938 0.156,0.198 10 false A 2.146,0.74 2.302,0.938 0.156,0.198 10 false B 2.625,0.875 2.938,1.073 0.313,0.198 10 false *3
*1 Driver Side Squib
*2 Spiral Cable Sub-Assembly
*3 Airbag ECU Assembly


Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the horn button assembly and airbag ECU assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.
C281403C03
1.177,2.292 1.51,2.531 0.333,0.24 0.177,1.167 0.188,0.688 false 2.083,0.552 1.938,0.208 false 2.031,2.396 1.813,1.875 true 2.198,2.396 2.552,1.875 true 0.115,1.198 0.427,1.354 0.313,0.156 10 false *1 1.042,0.563 1.354,0.719 0.313,0.156 10 false *2 2.896,0.708 3.208,0.865 0.313,0.156 10 false *3 1.792,0.135 2.104,0.292 0.313,0.156 10 false *4 1.052,1.615 1.365,1.771 0.313,0.156 10 false *a 0.667,0.542 0.823,0.771 0.156,0.229 10 false E 0.354,0.542 0.51,0.771 0.156,0.229 10 false F 2.563,0.542 2.771,0.781 0.208,0.24 10 false A 1.802,0.542 2.01,0.781 0.208,0.24 10 false C 2.25,0.542 2.458,0.781 0.208,0.24 10 false B 1.5,0.542 1.708,0.781 0.208,0.24 10 false D 1.26,2.323 1.573,2.521 0.313,0.198 10 false F9 1.594,1.792 1.906,1.948 0.313,0.156 10 false D+ 2.594,1.771 2.906,1.927 0.313,0.156 10 false D-
*1 Driver Side Squib
*2 Spiral Cable Sub-Assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Spiral Cable Sub-Assembly (Driver Side Squib))


Restore the released activation prevention mechanism of connector B to the original condition.


b.

Disconnect the instrument panel wire from the spiral cable sub-assembly.


c.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F9-1 (D+) - Body ground Ignition switch ON Below 1 V
F9-2 (D-) - Body ground Ignition switch ON Below 1 V




d.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-1 (D+) - F9-2 (D-) Always Below 1 Ω




e.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-1 (D+) - Body ground Always 1 MΩ or higher
F9-2 (D-) - Body ground Always 1 MΩ or higher




f.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-1 (D+) - F9-2 (D-) Always 1 MΩ or higher




g.

Restore the released activation prevention mechanism of connector B to the original condition.


Result:
Proceed to
OK
NG



OK

6.CHECK SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK SPIRAL CABLE SUB-ASSEMBLY
a.
C281423C01
0.521,2.188 0.833,2.417 0.313,0.229 1.99,1.104 2.073,0.688 false 0.188,1.125 0.219,0.698 false 2.563,0.542 2.719,0.74 0.156,0.198 10 false A 2.24,0.542 2.396,0.74 0.156,0.198 10 false B 1.813,0.542 1.969,0.74 0.156,0.198 10 false C 1.5,0.552 1.656,0.75 0.156,0.198 10 false D 0.667,0.542 0.823,0.74 0.156,0.198 10 false E 0.333,0.542 0.49,0.74 0.156,0.198 10 false F 0.104,1.156 0.417,1.354 0.313,0.198 10 false *1 1.052,0.542 1.365,0.74 0.313,0.198 10 false *2 2.917,0.688 3.229,0.885 0.313,0.198 10 false *3 1.927,1.135 2.24,1.333 0.313,0.198 10 false *4 0.615,2.219 0.927,2.417 0.313,0.198 10 false z3 0.24,1.615 0.552,1.813 0.313,0.198 10 false *a
*1 Driver Side Squib
*2 Spiral Cable Sub-Assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Horn Button Assembly (Driver Side Squib))


Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z3-2 - Body ground Ignition switch ON Below 1 V
z3-1 - Body ground Ignition switch ON Below 1 V




b.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-2 - z3-1 Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-2 - Body ground Always 1 MΩ or higher
z3-1 - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-2 - z3-1 Always 1 MΩ or higher




e.

Restore the released activation prevention mechanism of connector D to the original condition.


Result:
Proceed to
OK
NG



OK

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY