The meter CPU receives vehicle speed signals from the brake actuator assembly (skid control ECU) via the CAN communication system (CAN V Bus). The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly (skid control ECU). The brake actuator assembly (skid control ECU) supplies power to the vehicle speed sensor. The brake actuator assembly (skid control ECU) detects vehicle speed signals based on the pulses of the voltage.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly (skid control ECU) stores the DTCs. Troubleshoot the Anti-lock Brake System.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1275
The combination meter assembly controls the speedometer in accordance with vehicle speed signals from the speedometer sensor.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
Before starting the following inspection, check tire size and tire air pressure.
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| w/ ABS | A |
| w/o ABS | B |
A
B
Check if CAN communication DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication DTCs are output. | A |
| CAN communication DTCs are not output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Combination Meter / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Speed Meter Operation | Speedometer | OFF, 0, 40, 80, 120, 160, 200 | - |
| Tester Display |
|---|
| Speed Meter Operation |
Speedometer indication is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed Meter | Vehicle speed | Min.: 0 km/h
(0 mph) Max.: 255 km/h (158 mph) |
Almost the same as actual vehicle speed | - |
| Tester Display |
|---|
| Vehicle Speed Meter |
Vehicle speed displayed on the GTS is almost the same as the speedometer indication.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if anti-lock brake system DTCs are output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Anti-lock brake system DTCs are not output. | A |
| Anti-lock brake system DTCs are output. | B |
A
B
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Speed Meter Operation | Speedometer | OFF, 0, 40, 80, 120, 160, 200 | - |
| Tester Display |
|---|
| Speed Meter Operation |
Speedometer indication is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the speedometer sensor.
Click hereDrivetrain>C50 MANUAL TRANSMISSION / TRANSAXLE>SPEEDOMETER SENSOR(w/o ABS)>REMOVAL
Inspect the speedometer sensor.
Click hereDrivetrain>C50 MANUAL TRANSMISSION / TRANSAXLE>SPEEDOMETER SENSOR(w/o ABS)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F38 combination meter assembly connector.
Disconnect the B22 speedometer sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F38-34 (SI) - B22-3 (SI) | Always | Below 1 Ω |
| F38-34 (SI) or B22-3 (SI) - Body ground | Always | 10 kΩ or higher |
Reconnect the F38 combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B22-1 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG