1.REMOVE FRONT SEAT ASSEMBLY RH (for LHD)
2.REMOVE FRONT SEAT ASSEMBLY LH (for RHD)
3.REMOVE REAR SEAT ASSEMBLY (for Fixed Seat Type)
4.REMOVE REAR SEAT ASSEMBLY (for Separate Seat Type)
62112
5.REMOVE COWL SIDE TRIM BOARD LH
Remove the clip.
Disengage the 2 clips and the guide and remove the cowl side trim board LH.
62111C
6.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
62312B
7.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Remove the front door opening trim weatherstrip LH.
62311B
8.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62212
9.REMOVE FRONT PILLAR GARNISH LH
except 6 speakers:
Disengage the 2 clips and the 2 guides and remove the front pillar garnish LH.
for 6 speakers:
Disengage the 2 clips and the 2 guides.
Disconnect the connector and remove the front pillar garnish LH.
62211
10.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
62332A
11.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Remove the rear door opening trim weatherstrip LH.
62331A
12.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
73220
13.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
73210
14.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62414A
15.REMOVE CENTER PILLAR LOWER GARNISH LH
Disengage the 2 claws and the 2 clips and the 2 guides and remove the center pillar lower garnish LH.
62413A
16.REMOVE CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
62412B
17.REMOVE CENTER PILLAR UPPER GARNISH LH
Remove the 2 screws.
Disengage the clip.
Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.
62411B
18.REMOVE CENTER PILLAR UPPER GARNISH RH
Use the same procedure as for the LH side.
73370
19.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
73360
20.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62552F
21.REMOVE REAR SEAT SIDE GARNISH LH
for Separate Seat Type:
Remove the clip.
Disengage the 2 claws and the clip and the 2 guides and remove the rear seat side garnish LH.
for Fixed Seat Type:
Disengage the 2 claws and the clip and the 2 guides and remove the rear seat side garnish LH.
62551F
22.REMOVE REAR SEAT SIDE GARNISH RH
Use the same procedure as for the LH side.
62472A
23.REMOVE ROOF SIDE INNER GARNISH LH
Disengage the 4 clips.
Disengage the guide and remove the roof side inner garnish LH.
62471A
24.REMOVE ROOF SIDE INNER GARNISH RH
Use the same procedure as for the LH side.
81260A
25.REMOVE MAP LIGHT ASSEMBLY
74610A
26.REMOVE ASSIST GRIP SUB-ASSEMBLY
Use the same procedure to remove all assist grip sub-assemblies.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 assist grip covers.
Do not forcibly pry the assist grip covers to prevent them from being deformed.
Disengage the 2 clips and remove the assist grip.
Remove the 2 clips from the vehicle body.
63339A
27.REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/ Cover)
Use the same procedure to remove all roof headlining service hole covers.
Using a clip remover, remove the 2 roof headlining service hole covers.
74320
28.REMOVE VISOR ASSEMBLY LH
Disengage the guide.
Remove the 2 screws and visor assembly LH.
74310
29.REMOVE VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74348C
30.REMOVE VISOR HOLDER LH
Turn the visor holder LH approximately 45° and pull it out as shown in the illustration.
Disengage the 2 claws and remove the visor holder LH.
74348B
31.REMOVE VISOR HOLDER RH
Use the same procedure as for the LH side.
32.REMOVE ROOF HEADLINING ASSEMBLY
for front pillar RH side:
Disconnect the connector.
Remove the bolt.
Disengage the guide.
Using a clip remover, remove the 2 clamps.
| *a | Clamp | *b | Guide |
for front pillar LH side:
Disconnect the connector.
Using a clip remover, remove the 2 clamps.
for rear pillar RH side:
Disconnect the connector.
Using a clip remover, remove the clamp.
Using a clip remover, remove the 4 clips.
Remove the roof headlining assembly from the vehicle through the rear passenger side door.
Do not damage the roof headlining assembly or body interior.