Home › Suspension › REAR SUSPENSION › REAR AXLE BEAM(for Rear Disc Brake) › 2013.08–2017.10
RM30M0E _53 Suspension _017096 REAR SUSPENSION _0090105 REAR AXLE BEAM(for Rear Disc Brake) A

REAR SUSPENSION  REAR AXLE BEAM(for Rear Disc Brake)  REMOVAL  


PROCEDURE

Hide 1.REMOVE REAR WHEELS

Hide 89516D 3.SEPARATE SKID CONTROL SENSOR WIRE LH

Hide 89516C 4.SEPARATE SKID CONTROL SENSOR WIRE RH

HINT:

Use the same procedure described for the LH side.


Hide 47319F 5.SEPARATE REAR FLEXIBLE HOSE LH

Hide 47318F 6.SEPARATE REAR FLEXIBLE HOSE RH

HINT:

Use the same procedure described for the LH side.


Hide 47324 7.REMOVE REAR NO. 4 BRAKE TUBE

a.
C284390

Using a 10 mm union nut wrench, remove the rear No. 4 brake tube while holding the rear flexible hose with a wrench.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line.




b.

Remove the clip and separate the rear flexible hose.


Hide 47323 8.REMOVE REAR NO. 3 BRAKE TUBE

HINT:

Use the same procedure described for the rear No. 4 brake tube.


Hide 58251D 9.REMOVE FRONT FLOOR PANEL BRACE LH

Hide 58251D 10.REMOVE FRONT FLOOR PANEL BRACE RH

HINT:

Use the same procedure described for the LH side.


Hide 12.LOOSEN PARKING BRAKE CABLE

Hide 46430 13.SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 14.SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Use the same procedure described for the No. 3 parking brake cable assembly.


Hide 15.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY LH

Hide 16.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 42450B 18.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH

Hide 42450A 19.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 42110F 20.LOOSEN REAR AXLE BEAM ASSEMBLY

Hide 48231B 21.REMOVE REAR COIL SPRING LH

Hide 48231A 22.REMOVE REAR COIL SPRING RH

HINT:

Use the same procedure described for the LH side.


Hide 42110F 23.REMOVE REAR AXLE BEAM ASSEMBLY

a.

Support the rear axle beam assembly with an engine lifter using the 4 plate lift attachments or equivalent tools as shown in the illustration.

C282509C01
2.073,2.417 2.438,2.052 false 2.49,1.656 2.271,1.75 false 3.323,1.688 3.125,1.688 false 4.052,1.698 3.854,1.698 false 5.063,1.719 4.823,1.625 false 2.51,1.542 2.74,1.698 0.229,0.156 10 true *a 1.896,2.344 2.208,2.5 0.313,0.156 10 false *b 3.344,1.625 3.573,1.781 0.229,0.156 10 true *a 3.698,1.615 3.927,1.771 0.229,0.156 10 true *a 4.656,1.542 4.885,1.698 0.229,0.156 10 true *a 1.865,1.781 1.99,1.927 0.125,0.146 10 true A 5.333,1.771 5.458,1.917 0.125,0.146 10 true A 0.271,1.938 0.396,2.083 0.125,0.146 10 true B 6.875,1.948 7,2.094 0.125,0.146 10 true B
*a Plate Lift Attachment *b Engine Lifter


NOTICE:

Make sure to secure the rear axle beam assembly to prevent it from dropping.



b.

Remove the 2 bolts A and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.


c.

Remove the 2 bolts B and rear axle beam assembly from the body.


Hide 48725G 24.REMOVE REAR AXLE CARRIER BUSH LH

a.
C289568C01
1.042,2.635 1.385,2.458 1.385,2.458 1.031,1.99 true 0.271,2.99 0.646,2.667 true 1.979,2.135 2.573,2.083 2.573,2.083 1.906,1.625 true 2.531,2.073 1.813,1.781 true 1.438,2.396 1.615,2.552 0.177,0.156 10 false *a 0.115,2.938 0.333,3.094 0.219,0.156 10 false *b 1.75,0.292 2.063,0.448 0.313,0.156 10 false *c 3.198,1.25 3.406,1.417 0.208,0.167 10 false *d 2.646,2 3.104,2.198 0.458,0.198 10 false SST
*a Bush Rib
*b Alignment Mark
*c Hold
*d Turn


Place a matchmark on the rear axle beam assembly with it aligned with the alignment mark of the rear axle carrier bush LH.


b.

Using a chisel and hammer, bend the 2 portions of the bush rib.

NOTICE:
·

Bend the bush rib until the claw of SST can be suspended.

·

When removing the bush, do not rub off the matchmark on the rear axle beam assembly.




c.

Using SST, remove the rear axle carrier bush LH from the rear axle beam assembly.

SST
09710-26011  (09710-05061)
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011)
09950-60010  (09951-00530)

NOTICE:

Apply grease to the threads and tip of the SST center bolt before use.



Hide 48725F 25.REMOVE REAR AXLE CARRIER BUSH RH

HINT:

Use the same procedure described for the LH side.