Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2013.08–2016.04
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0090108 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1541  Vehicle Speed Signal Malfunction  C1542  Vehicle Speed Signal Malfunction  C1571  Speed Sensor Malfunction (Test Mode DTC)  


DESCRIPTION

Based on the vehicle speed signal received from the combination meter assembly, the power steering ECU assembly adjusts the amount of power assist according to the vehicle speed. The power steering ECU assembly monitors the speed signal input and stores a DTC if a malfunction is detected. While a malfunction exists in the vehicle speed signal, fail-safe operation maintains the amount of power assist at the level used for a speed of 70 km/h (43 mph).

NOTICE:

Revving the engine while the vehicle is stopped may cause DTC C1541 or C1542 to be stored.


HINT:
·

If C1541 is stored while the vehicle is stopped, driving the vehicle for 5 minutes or more and then turning the ignition switch off will clear the DTC.

·

If C1542 is stored while the vehicle is stopped, driving the vehicle for 5 minutes or more will clear the DTC.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. Each ECU controls its respective system based on the vehicle speed pulse signal.

·

If a short occurs in any of the ECUs or in a wire harness connected to an ECU, all systems in the diagram below will not operate normally.



DTC No. Detection Item DTC Detection Condition Trouble Area Return-to-normal Condition Note
C1541 Vehicle Speed Signal Malfunction
·

A vehicle speed signal indicating an abnormal increase in vehicle speed.

·

While the vehicle is stopped, the engine speed exceeds the threshold* for a total of 300 seconds or more.


·

Vehicle speed signal circuit

·

Combination meter assembly

·

Power steering ECU assembly


Ignition switch turned to ON again or after system confirmed to be normal Power Steering Warning Light comes on.
C1542 Vehicle Speed Signal Malfunction
·

A vehicle speed signal indicating an abnormal decrease in vehicle speed.

·

While the vehicle is stopped, the engine speed exceeds the threshold* for a total of 30 seconds or more.


·

Vehicle speed signal circuit

·

Combination meter assembly

·

Power steering ECU assembly


Ignition switch turned to ON again or after system confirmed to be normal Power Steering Warning Light does not illuminate (normal reset).
C1571 Speed Sensor Malfunction (Test Mode DTC) A speed sensor malfunction (Test Mode DTC).
·

Vehicle speed signal circuit

·

Combination meter assembly

·

Power steering ECU assembly


- Power Steering Warning Light does not illuminate (normal reset).

*: Threshold: An engine speed of 4000 rpm or more is detected within 5 minutes after the engine is started, or an engine speed of 2100 rpm or more is detected 5 minutes or more after the engine is started.

C225498E04
0.576,0.668 0.921,0.825 0.344,0.156 10 4000 0.576,1.016 0.928,1.176 0.352,0.16 10 2100 0.307,0.22 1.595,0.391 1.288,0.172 10 Engine speed (rpm) 0.845,1.471 0.949,1.628 0.104,0.156 10 0 2.373,1.475 3.017,1.642 0.645,0.167 10 5 minutes 1.953,0.053 6.143,0.213 4.19,0.16 10 C1542 stored when value exceeds threshold for total of 30 seconds 1.919,0.117 1.819,0.117 1.819,0.117 1.422,0.642 false 1.743,0.35 6.002,0.51 4.259,0.16 10 C1541 stored when value exceeds threshold for total of 300 seconds 4.304,1.472 6.246,1.629 1.942,0.157 10 Elapsed time after engine start 5.42,0.968 6.144,0.607 6.144,0.607 6.144,0.406 false 6.144,0.406 6.045,0.406 false


WIRING DIAGRAM

C280660E01
1.365,0.75 1.677,0.948 0.313,0.198 10 false 35 1.104,0.885 1.417,1.083 0.313,0.198 10 false +S 4.854,0.875 5.167,1.073 0.313,0.198 10 false F12 4.938,1.927 5.083,2.135 0.146,0.208 10 false 2 5.229,0.875 5.604,1.073 0.375,0.198 10 false SPD 4.865,2.156 5.177,2.354 0.313,0.198 10 false F11 4.917,0.667 5.063,0.875 0.146,0.208 10 false 2 5.219,2.146 5.667,2.344 0.448,0.198 10 false PGND 0.469,1.698 0.781,1.896 0.313,0.198 10 false F38 0.458,1.885 1.667,2.479 1.208,0.594 10 false Combination Meter Assembly 5.083,2.906 7.125,3.469 2.042,0.563 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly, electric power steering column sub-assembly or power steering motor assembly have been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


PROCEDURE

1.PERFORM SIGNAL CHECK (VEHICLE SPEED SIGNAL)
a.

Perform the signal check in the Test Mode procedure.

Chassis > EMPS > Utility
Tester Display
Signal Check
50005 13 3
OK:

Test mode DTC C1571 is cleared.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK METER / GAUGE SYSTEM
2.CHECK METER / GAUGE SYSTEM
a.

The circuits that send vehicle speed signals to this system are inspected in the meter / gauge system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction


b.

During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.


Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - POWER STEERING ECU ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the F12 power steering ECU assembly connector.


b.

Disconnect the F38 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-2 (SPD) - F38-35 (+S) Always Below 1 Ω
F12-2 (SPD) or F38-35 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT POWER STEERING ECU ASSEMBLY (SPD SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER STEERING ECU ASSEMBLY (SPD SIGNAL)
a.
C270049C03
2.948,1.625 3.323,1.865 0.375,0.24 1.094,1.646 1.469,1.885 0.375,0.24 1.177,2.375 0.813,1.74 true 2.708,2.396 2.344,1.76 true 0.063,0.031 0.375,0.188 0.313,0.156 10 false *a 1.167,1.677 1.479,1.865 0.313,0.188 10 false F12 3.01,1.656 3.323,1.844 0.313,0.188 10 false F11 1.063,2.385 1.646,2.594 0.583,0.208 10 false SPD 2.542,2.406 3.271,2.615 0.729,0.208 10 false PGND 2.833,3.802 3.292,4 0.458,0.198 10 false GND
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connectors.


b.

Use a lift to raise the vehicle until the tires are off the ground.


c.

Start the engine.


d.

Depress the clutch pedal*1 or brake pedal*2.


e.

Move the shift lever to the 1st position*1 or shift lever to D*2.


f.

Engage the clutch*1 or slowly release the brake pedal*2.


g.

Check that the front wheels rotate slowly.

CAUTION:

Be careful not to get caught in the front wheels while they are rotating.



h.

Check the signal waveform according to the condition(s) in the table below.

OK:
Tester Connection Condition Specified Condition
F12-2 (SPD) -F11-2 (PGND) Front wheels rotating at speed corresponding to vehicle speed of approximately 20 km/h (12 mph) Correct waveform appears as shown


Tool Setting
Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle Condition Vehicle being driven at approximately 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.


*1: for Manual Transaxle

*2: for Automatic Transaxle



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY