Home › Steering › STEERING COLUMN › STEERING WHEEL › 2013.08–2017.10
RM30M0E _55 Steering _017104 STEERING COLUMN _0090117 STEERING WHEEL A

STEERING COLUMN  STEERING WHEEL  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS. Read the precautionary notices concerning the SRS before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 2.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Hide 45186 4.REMOVE NO. 2 STEERING WHEEL LOWER COVER

a.
B346971C01
1.135,0.74 1.448,0.333 true 1.469,0.219 1.781,0.417 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the No. 2 steering wheel lower cover.


Hide 45130 5.REMOVE HORN BUTTON ASSEMBLY (w/ Airbag System)

Hide 45130 6.REMOVE HORN BUTTON ASSEMBLY (w/o Airbag System)

a.
C289562C01
0.385,1.281 0.49,1.052 true 0.896,0.844 1.125,0.708 true 1.115,0.615 1.271,0.771 0.156,0.156 10 true *1 0.521,0.917 0.708,1.073 0.188,0.156 10 true *a
*1 Torsion Spring
*a TORX Driver


Using a "TORX" driver, push in the 3 torsion springs to disengage the 3 pins.

NOTICE:

Do not drop the horn button assembly.



b.

Pull out the horn button assembly from the steering wheel assembly and support the horn button assembly with one hand.


c.

Disconnect the horn connector.


Hide 45100 7.REMOVE STEERING WHEEL ASSEMBLY

a.
C286519C01
0.865,0.667 1.281,0.479 1.281,0.479 0.854,0.542 true 1.313,0.396 1.542,0.552 0.229,0.156 10 true *a
*a Matchmark


Remove the steering wheel set nut.


b.

Put matchmarks on the steering wheel assembly and steering main shaft.


c.

Disconnect all the connectors from the spiral cable sub-assembly.


d.
C286520C01
2.323,1.667 2.896,1.115 true 0.667,3.135 0.865,3.323 0.198,0.188 10 true *a 3.219,2.198 3.427,2.354 0.208,0.156 10 true *b 2.927,1.021 3.292,1.229 0.365,0.208 10 true SST
*a Hold
*b Turn


Using SST, remove the steering wheel assembly.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



Hide 45116 8.REMOVE NO. 1 STEERING WHEEL ORNAMENT (w/ Steering Wheel Ornament)

a.
C289131

Remove the 2 screws.


b.

Disengage the 4 claws and 5 pins and remove the No. 1 steering wheel ornament.


Hide 84250A 9.REMOVE STEERING PAD SWITCH ASSEMBLY (w/ Steering Pad Switch)

Hide 45184 10.REMOVE LOWER STEERING WHEEL BOSS COVER

a.
C284825

Disengage the 6 claws and remove the lower steering wheel boss cover.