Refer to DTC P0031.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>P0031
Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0136 | Oxygen Sensor Circuit (Bank 1 Sensor 2) | Following conditions (a) and (b) met for 6 minutes or more after engine warmed up (2 trip detection logic):
(a) Vehicle driven in 1 STOP-and-GO* cycles (b) Heated oxygen sensor (sensor 2) voltage remains at 0.4 V or higher or 0.5 V or less |
·
Open or short in heated oxygen sensor (sensor 2) circuit ·
Heated oxygen sensor (sensor 2) ·
Heated oxygen sensor (sensor 2) heater |
Comes on | DTC stored |
*: STOP refers to a vehicle speed of less than 5 km/h (3 mph) and GO refers to a vehicle speed of 100 km/h (62 mph) or more.
The ECM monitors the heated oxygen sensor (sensor 2) to check for the following malfunctions. If any of the malfunctions are detected, the ECM illuminates the MIL and stores a DTC.
The heated oxygen sensor (sensor 2) output voltage remains above 0.5 V (rich) or below 0.4 V (lean) while the vehicle is accelerated and decelerated for 4 minutes or more.
| Required Sensor/Components (Main) | Heated oxygen sensor (sensor 2) |
| Required Sensor/Components (Related) | Engine coolant temperature sensor
Mass air flow meter Vehicle speed sensor Throttle body with motor assembly |
| Frequency of operation | Once per driving cycle |
| All of the following conditions A to C are met | - |
| A. Engine | Running |
| B. Time after engine starts | 0 seconds or more |
| C. Cumulative time while heated oxygen sensor is ON | 22 seconds or more |
| All of the following conditions are met | - |
| Frequency of switch time between less than 0.4 V and 0.5 V or higher | 0 times |
| Cumulative rear oxygen sensor monitor time | 190 seconds or more |
Connect the GTS to the DLC3.
Turn the ignition switch on and turn the GTS on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch and turn the GTS on.
Start the engine and idle it for 60 seconds or more [A].
Drive the vehicle at more than 100 km/h (62 mph) for 5 minutes or more [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Allow the engine to idle for 10 seconds or more [C].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read the pending DTC.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0136.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D].
Refer to DTC P0031.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>P0031
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the GTS.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / O2S B1S1 and O2S B1S2.
Perform the Active Test operation with the engine idling (press the 12.5% or -12.5% button to change the fuel injection volume).
Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the GTS.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
| GTS Display
(Sensor) |
Injection Volume | Status | Voltage |
|---|---|---|---|
| O2S B1S1
Heated oxygen sensor (sensor 1) |
12.5% | Rich | Higher than 0.5 V |
| -12.5% | Lean | Below 0.4 V | |
| O2S B1S2
Heated oxygen sensor (sensor 2) |
12.5% | Rich | Higher than 0.5 V |
| -12.5% | Lean | Below 0.4 V |
The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.
Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the heated oxygen sensors.
To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / O2S B1S1 and O2S B1S2, and then press the graph button on the Data List view.
If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0136 will be stored.
Inspect the fuses for circuits related to this system before performing the following procedure.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0136 is output | A |
| DTC P0136 and other DTCs are output | B |
If any DTCs other than P0136 are output, troubleshoot those DTCs first.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S2.
| Tester Display |
|---|
| O2S B1S2 |
Allow the engine to run at 2500 rpm for 3 minutes.
Depress the accelerator pedal quickly until the engine rpm reaches 4000 rpm 3 times.
Heated oxygen sensor voltage alternates between below 0.4 V and 0.5 V or higher.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Inspect the heated oxygen sensor (sensor 2).
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR(for Sensor 2)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Heated Oxygen Sensor (Sensor 2)) |
Disconnect the heated oxygen sensor (sensor 2) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F58-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F58 heated oxygen sensor (sensor 2) connector.
Disconnect the F82 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connections | Condition | Specified Condition |
|---|---|---|
| F58-1 (HT1B) - F82-6 (HT1B) | Always | Below 1 Ω |
| F58-3 (OX1B) - F82-27 (OX1B) | Always | Below 1 Ω |
| F58-4 (E2) - F82-26 (EX1B) | Always | Below 1 Ω |
| F58-1 (HT1B) - F82-6 (HT1B) - Body ground | Always | 10 kΩ or higher |
| F58-3 (OX1B) - F82-27 (OX1B) - Body ground | Always | 10 kΩ or higher |
| F58-4 (E2) - F82-26 (EX1B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F58 heated oxygen sensor (sensor 2) connector.
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F58-2 (+B) - 2H-4 | Always | Below 1 Ω |
| F58-2 (+B) or 2H-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0136 is output | A |
| DTC is not output | B |
A
B