When the ignition switch is turned to ON, the battery voltage is applied to IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the EFI relay and supplying power to either terminal +B of the ECM.
Inspect the fuses for circuits related to this system before performing the following procedure.
Disconnect the B32 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B32-1 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
Disconnect the ECM connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F81-21 (IGSW) - Body ground | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ smart entry and start system) | B |
| NG (w/o smart entry and start system) | C |
A
B
C
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2B-1 - 2K-4 | When battery voltage not applied to terminals 2L-9 and 2J-7 | 10 kΩ or higher |
| When battery voltage applied to terminals 2L-9 and 2J-7 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Disconnect the F81 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-2 (MREL) - 2L-9 | Always | Below 1 Ω |
| F81-10 (+B) - 2K-4 | Always | Below 1 Ω |
| F81-2 (MREL) or 2L-9 - Body ground | Always | 10 kΩ or higher |
| F81-10 (+B) or 2K-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2J-7 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>PROBLEM SYMPTOMS TABLE
NG
Inspect the No. 2 ignition relay.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F81 ECM connector.
Remove the No. 2 ignition relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-21 (IGSW) - F77-5 (No. 2 ignition relay) | Always | Below 1 Ω |
| F81-21 (IGSW) or F77-5 (No. 2 ignition relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 2 ignition relay) |
Remove the No. 2 ignition relay.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F77-3 (No. 2 ignition relay) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 ignition relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F77-1 (No. 2 ignition relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Remove the No. 2 ignition relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-20 (IG1D) - F77-2 (No. 2 ignition relay) | Always | Below 1 Ω |
| F43-20 (IG1D) or F77-2 (No. 2 ignition relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the No. 2 ignition relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F77-2 (No. 2 ignition relay) - 2H-5 | Always | Below 1 Ω |
| F77-2 (No. 2 ignition relay) or 2H-5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>1NZ-FE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F7 ignition or starter switch assembly connector.
Disconnect the F81 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-21 (IGSW) - F7-6 (IG2) | Always | Below 1 Ω |
| F81-21 (IGSW) or F7-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Disconnect the F7 ignition or starter switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F7-6 (IG2) - 2H-5 | Always | Below 1 Ω |
| F7-6 (IG2) or 2H-5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Driver side junction block assembly) |
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2B-1 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG