The fuel injectors inject fuel based on the signals from the ECM.
Inspect the fuses for circuits related to this system before performing the following procedure.
| *a | Front view of wire harness connector
(to Fuel Injector Assembly) |
Disconnect the fuel injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B4-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B5-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B6-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B7-1 - Body ground | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ smart entry and start system) | B |
| NG (w/o smart entry and start system) | C |
A
B
C
Inspect the fuel injector assembly.
Click hereEngine / Hybrid System>1NZ-FE FUEL>FUEL INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B4, B5, B6 and B7 fuel injector assembly connectors.
Disconnect the B32 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B4-2 - B32-4 (#10) | Always | Below 1 Ω |
| B5-2 - B32-3 (#20) | Always | Below 1 Ω |
| B6-2 - B32-11 (#30) | Always | Below 1 Ω |
| B7-2 - B32-13 (#40) | Always | Below 1 Ω |
| B4-2 or B32-4 (#10) - Body ground | Always | 10 kΩ or higher |
| B5-2 or B32-3 (#20) - Body ground | Always | 10 kΩ or higher |
| B6-2 or B32-11 (#30) - Body ground | Always | 10 kΩ or higher |
| B7-2 or B32-13 (#40) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>PROBLEM SYMPTOMS TABLE
NG
Disconnect the B4, B5, B6 and B7 fuel injector assembly connectors.
Remove the No. 2 ignition relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B4-1 - F77-5 | Always | Below 1 Ω |
| B5-1 - F77-5 | Always | Below 1 Ω |
| B6-1 - F77-5 | Always | Below 1 Ω |
| B7-1 - F77-5 | Always | Below 1 Ω |
| B4-1 or F77-5 - Body ground | Always | 10 kΩ or higher |
| B5-1 or F77-5 - Body ground | Always | 10 kΩ or higher |
| B6-1 or F77-5 - Body ground | Always | 10 kΩ or higher |
| B7-1 or F77-5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B4, B5, B6 and B7 fuel injector assembly connectors.
Disconnect F7 ignition or starter switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B4-1 - F7-6 (IG2) | Always | Below 1 Ω |
| B5-1 - F7-6 (IG2) | Always | Below 1 Ω |
| B6-1 - F7-6 (IG2) | Always | Below 1 Ω |
| B7-1 - F7-6 (IG2) | Always | Below 1 Ω |
| B4-1 or F7-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| B5-1 or F7-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| B6-1 or F7-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| B7-1 or F7-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG