77218A
1.INSTALL NO. 3 FUEL TANK FILLER PIPE SUPPORT
| *a | Cutaway View |
|
Front of Vehicle |
Engage the clamp to install the No. 3 fuel tank filler pipe support to the fuel tank filler pipe assembly.
77216A
2.INSTALL NO. 1 FUEL TANK FILLER PIPE SUPPORT
| *a | Cutaway View |
|
Left Side of Vehicle |
Install the No. 1 fuel tank filler pipe support to the fuel tank filler pipe assembly.
77217C
3.INSTALL NO. 2 FUEL TANK FILLER PIPE SUPPORT
| *a | Cutaway View |
|
Left Side of Vehicle |
Engage the clamp to install the No. 2 fuel tank filler pipe support to the fuel tank filler pipe assembly.
77701W
4.INSTALL NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY
Connect the No. 1 canister outlet hose sub-assembly to the No. 6 fuel tank breather tube.
Engage the 2 clamps to install the No. 1 canister outlet hose sub-assembly to the fuel tank assembly.
77028F
5.INSTALL NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY
Engage the 2 clamps to install the No. 2 fuel emission tube sub-assembly to the fuel tank assembly.
77209F
6.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY
Engage the 2 clamps to install the fuel tank main tube sub-assembly to the fuel tank assembly.
77100
7.INSTALL FUEL TANK ASSEMBLY
Clean and degrease the bolt holes.
Using an engine lifter, set the fuel tank assembly.
Install the fuel tank assembly to the vehicle with 4 new bolts.
| *1 | Fuel Tank Filler Pipe Sub-assembly |
| *2 | No. 1 Fuel Tank Breather Tube |
Connect the fuel tank filler pipe sub-assembly and No. 1 fuel tank breather tube to the No. 3 fuel tank filler pipe support.
Engage the clamp to install the fuel tank filler pipe flange plate to the No. 3 fuel tank filler pipe support.
Install the fuel tank filler pipe flange plate to the vehicle with the bolt.
Engage the 2 clamps to connect the No. 6 fuel tank breather tube.
| *1 | No. 6 Fuel Tank Breather Tube |
| *a | Clamp |
| *b | Rib |
Install the No. 6 fuel tank breather tube so that its 2 ribs are between the 2 clamps as shown in the illustration.
77209F
8.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
| *1 | Retainer |
|
Push |
Line up the fuel main tube and fuel tube connector, and push them together until a "click" sound is heard. If the fuel main tube is difficult to push into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel main tube and reinsert it.
Push down the retainer.
Check that there is no damage or foreign matter around the connecting parts of the fuel tube connector and fuel main tube before starting this step.
After connecting the fuel tube connector, check that it is securely connected by pulling on it.
77028F
9.CONNECT NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY
Connect the No. 2 fuel emission tube sub-assembly to the fuel tank to canister tube with the hose clip.
46420
10.CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY
Connect the No. 2 parking brake cable assembly to the vehicle with the 2 bolts.
77641A
11.INSTALL NO. 1 FUEL TANK PROTECTOR
Install the No. 1 fuel tank protector to the vehicle with the bolt and clip.
58156
12.INSTALL NO. 4 FRONT FLOOR HEAT INSULATOR
Install the No. 4 front floor heat insulator to the vehicle with the 2 nuts.
17410
13.INSTALL FRONT EXHAUST PIPE ASSEMBLY
57533B
14.INSTALL FRONT FLOOR CENTER BRACE
58910C
15.INSTALL REAR CONSOLE BOX ASSEMBLY
16.INSTALL REAR WHEEL LH
77020A
17.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
18.ADD FUEL
77310A
19.INSTALL FUEL TANK CAP ASSEMBLY
20.INSPECT FOR FUEL LEAK
21.INSPECT EXHAUST GAS LEAK