Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  U0073  Control Module Communication Bus OFF  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives the signals from the ECM via the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0073 Control Module Communication Bus OFF When the IG1 terminal voltage is between 10 and 17.4 V, the condition that bus OFF state occurs once or more within 0.1 seconds occurs 10 times in succession. (Sent signals cannot be received.) CAN communication system

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EFI Communication Open EFI communication open detection Normal or Error Normal: Normal
Error: Momentary interruption
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
EFI Communication Open
50003 105 204

Result:
Result Proceed to
There is a constant open circuit A
There are no momentary interruptions B
There are momentary interruptions C


HINT:

Perform the above inspection before disconnecting any sensors or connectors.



A

2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED

B

3.RECONFIRM DTC

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED
a.

Turn the ignition switch off.


b.

Check if each sensor or ECM connector is securely connected.

OK:

Each connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY

3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Record the output DTCs.

for Anti-lock Brake System

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

for CAN Communication System

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

HINT:

If CAN communication system DTCs and related sensor DTCs are output simultaneously, troubleshoot the DTCs (for Anti-lock Brake System) after the CAN communication system returns to normal.



Result:
Result Proceed to
DTC is not output A
DTC (relating to anti-lock brake system) is output B
DTC (relating to CAN communication system) is output C



A

B

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Turn the ignition switch off.


b.

Repair or replace the harness or connector.


c.

Check for any momentary interruption between the skid control ECU (brake actuator assembly) and each sensor or ECM.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


d.

Check that there is no momentary interruption.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.


e.

Check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


f.

If anti-lock brake system DTCs are output, record them.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC is not output A
DTC is output (relating to anti-lock brake system) B
DTC is output (relating to CAN communication system) C


HINT:

The CAN communication system must be normal when performing troubleshooting for sensor DTCs (for ABS system).



A

END

B

C