Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2013.08–2016.04
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1468  SFR Solenoid Circuit  C1469  SFL Solenoid Circuit  C146A  SRR Solenoid Circuit  C146B  SRL Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1468 SFR Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more. Brake actuator assembly
C1469 SFL Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more. Brake actuator assembly
C146A SRR Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more. Brake actuator assembly
C146B SRL Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more. Brake actuator assembly

WIRING DIAGRAM

C292140E01
1.469,1.354 2.26,1.573 0.792,0.219 10 false ABS NO. 2 0.677,2.542 1.135,2.74 0.458,0.198 10 false ALT 0.646,4.448 1.719,4.646 1.073,0.198 10 false FL MAIN 0.823,5.927 1.896,6.125 1.073,0.198 10 false Battery 3.188,1.052 3.5,1.25 0.313,0.198 10 false 12 3.5,1.063 3.958,1.26 0.458,0.198 10 false +BS 3.271,4.917 3.427,5.115 0.156,0.198 10 false 1 3.5,5.083 4.115,5.281 0.615,0.198 10 false GND1 4.531,1.177 6.677,1.375 2.146,0.198 10 false Solenoid Relay 5.917,1.958 6.531,2.156 0.615,0.198 10 false SFRH 5.917,2.458 6.531,2.656 0.615,0.198 10 false SFLH 5.927,2.958 6.542,3.156 0.615,0.198 10 false SRRH 5.927,3.458 6.542,3.656 0.615,0.198 10 false SRLH 5.927,3.958 6.542,4.156 0.615,0.198 10 false SFRR 5.927,4.469 6.542,4.667 0.615,0.198 10 false SFLR 5.938,4.958 6.552,5.156 0.615,0.198 10 false SRRR 5.927,5.448 6.542,5.646 0.615,0.198 10 false SRLR 4.385,4.01 6.833,4.208 2.448,0.198 10 false Skid Control ECU 4.26,7.813 4.719,8.01 0.458,0.198 10 false A35 4.25,8.021 6.188,8.333 1.938,0.313 10 false Brake Actuator Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the skid control ECU (brake actuator assembly).

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).


a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Start the engine.


c.

Drive the vehicle at the speed of 20 km/h (12 mph) or more for 30 seconds or more.


d.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC is not output A
DTC is output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.




A

B