44546A
1.INSTALL BRAKE ACTUATOR BRACKET CUSHION
Install the 3 brake actuator bracket cushions to the brake actuator bracket assembly.
Install the 3 brake actuator case collars to the 3 brake actuator bracket cushions.
44590
2.INSTALL BRAKE ACTUATOR BRACKET ASSEMBLY (for LHD)
Install the brake actuator bracket assembly to the brake actuator assembly with the 3 bolts in the sequence shown in the illustration.
Do not remove the hole plug before connecting the brake tube. New actuators are filled with brake fluid.
Do not carry the brake actuator assembly by the connector.
44590
3.INSTALL BRAKE ACTUATOR BRACKET ASSEMBLY (for RHD)
Install the brake actuator bracket assembly to the brake actuator assembly with the 3 bolts in the sequence shown in the illustration.
Do not remove the hole plug before connecting the brake tube. New actuators are filled with brake fluid.
Do not carry the brake actuator assembly by the connector.
44510
4.INSTALL BRAKE ACTUATOR ASSEMBLY (for LHD)
Install the brake actuator assembly with the brake actuator bracket assembly with the 3 bolts in the sequence shown in the illustration.
Do not damage the brake tubes or wire harness.
Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.
| *a | to Front Wheel Cylinder RH |
| *b | to Front Wheel Cylinder LH |
| *c | to Rear Wheel Cylinder RH |
| *d | to Rear Wheel Cylinder LH |
| *e | from Front Master Cylinder |
| *f | from Rear Master Cylinder |
Temporarily install each brake tube to the correct position on the brake actuator assembly as shown in the illustration.
Using a 10 mm union nut wrench, tighten the 6 brake tubes.
Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
| *a | Lock Lever |
Connect the brake actuator connector.
Make sure that the connector is locked securely.
Make sure that the brake actuator connector can be connected smoothly. Do not allow entry of water, oil or dirt.
44510
5.INSTALL BRAKE ACTUATOR ASSEMBLY (for RHD)
Install the brake actuator assembly with the brake actuator bracket assembly with the 3 bolts in the sequence shown in the illustration.
Do not damage the brake tubes or wire harness.
Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.
| *a | to Front Wheel Cylinder RH |
| *b | to Front Wheel Cylinder LH |
| *c | to Rear Wheel Cylinder RH |
| *d | to Rear Wheel Cylinder LH |
| *e | from Rear Master Cylinder |
| *f | from Front Master Cylinder |
Temporarily install each brake tube to the correct position on the brake actuator assembly as shown in the illustration.
Using a 10 mm union nut wrench, tighten the 6 brake tubes.
Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
| *a | Lock Lever |
Connect the brake actuator connector.
Make sure that the connector is locked securely.
Make sure that the brake actuator connector can be connected smoothly. Do not allow entry of water, oil or dirt.
74410
6.INSTALL BATTERY CARRIER ASSEMBLY
Install the battery carrier assembly to the body with the 6 bolts.
Engage the 6 clamps to install the wire harness to the battery carrier assembly.
74431
7.INSTALL BATTERY TRAY
28800
8.INSTALL BATTERY
9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
10.BLEED BRAKE LINE
11.BLEED CLUTCH LINE (for Manual Transaxle)
for C50
for C54
12.INSPECT BRAKE ACTUATOR USING GTS
13.CHECK AND CLEAR DTC