Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2013.08–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090604 AUTOMATIC TRANSAXLE SYSTEM C

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) One of the following conditions (A), (B) or (C) is met:
Condition (A):
Any 2 or more of the following signals are ON simultaneously (2 trip detection logic).
·

One of the following conditions is met.

P input signal is ON.

N input signal is ON.

NSW input signal is ON.

·

R input signal is ON.

·

D input signal is ON.

·

2 input signal is ON.

·

L input signal is ON.


Condition (B):
All switches are OFF simultaneously (2 trip detection logic).
·

P input signal is OFF.

·

N input signal is OFF.

·

NSW input signal is OFF.

·

R input signal is OFF.

·

D input signal is OFF.

·

2 input signal is OFF.

·

L input signal is OFF.


Condition (C):
When any of following conditions is met, the 3 position input signal is ON for 2 seconds or more (2 trip detection logic).
·

NSW input signal is ON.

·

P input signal is ON.

·

R input signal is ON.

·

N input signal is ON.

·

2 input signal is ON.

·

L input signal is ON.


·

Wire harness or connector

·

Park/neutral position switch

·

Transmission control switch (Shift lock control unit assembly)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM.

For safety, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch sends a signal to the ECM according to the shift position (P, R, N, D, 2 or L). The ECM determines that there is a problem with the switch or related parts if it receives 2 or more position signals simultaneously or it receives no position signal. The ECM turns on the MIL and stores the DTC.

WIRING DIAGRAM

C279799E08
0.208,0.625 1.042,0.813 0.833,0.188 10 false to ST Relay 0.25,2.302 1.26,2.469 1.01,0.167 10 false ECU-IG NO. 3 1.417,3.417 1.708,3.583 0.292,0.167 10 false B19 1.417,3.583 3.219,3.771 1.802,0.188 10 false Park/Neutral Position Switch 1.323,4.833 1.656,5 0.333,0.167 10 false F19 1.323,4.99 3.792,5.323 2.469,0.333 10 false Transmission Control Switch (Shift Lock Control Unit Assembly) 6.167,4.854 6.625,5.052 0.458,0.198 10 false ECM 1.552,4.292 1.708,4.49 0.156,0.198 10 false 1 2.927,4.281 3.083,4.479 0.156,0.198 10 false 2 1.75,0.771 1.906,0.969 0.156,0.198 10 false L 1.729,2.271 2.042,2.469 0.313,0.198 10 false RB 2.74,0.75 2.896,0.948 0.156,0.198 10 false B 2.667,1.313 2.885,1.479 0.219,0.167 10 false PL 2.677,1.698 2.906,1.875 0.229,0.177 10 false RL 2.677,2.063 2.885,2.229 0.208,0.167 10 false NL 2.688,2.438 2.917,2.604 0.229,0.167 10 false DL 2.688,2.823 2.865,3 0.177,0.177 10 false 2L 2.688,3.188 2.885,3.354 0.198,0.167 10 false LL 1.563,0.552 1.698,0.719 0.135,0.167 10 false 5 1.573,2.073 1.698,2.24 0.125,0.167 10 false 2 2.917,0.552 3.042,0.729 0.125,0.177 10 false 4 2.927,1.104 3.063,1.271 0.135,0.167 10 false 6 2.917,1.49 3.063,1.656 0.146,0.167 10 false 1 2.927,1.875 3.083,2.073 0.156,0.198 10 false 9 2.927,2.24 3.083,2.438 0.156,0.198 10 false 7 2.927,2.635 3.083,2.833 0.156,0.198 10 false 3 2.927,2.99 3.083,3.156 0.156,0.167 10 false 8 5.75,0.646 6.188,0.823 0.438,0.177 10 false NSW 5.76,1.188 5.917,1.385 0.156,0.198 10 false P 5.76,1.594 5.917,1.792 0.156,0.198 10 false R 5.76,1.958 5.917,2.156 0.156,0.198 10 false N 5.75,2.344 5.917,2.563 0.167,0.219 10 false D 5.76,2.719 5.917,2.917 0.156,0.198 10 false 2 5.76,3.115 5.917,3.313 0.156,0.198 10 false L 5.76,4.385 5.917,4.583 0.156,0.198 10 false 3 5.51,0.458 5.667,0.656 0.156,0.198 10 false 9 5.469,1.021 5.719,1.198 0.25,0.177 10 false 34 5.479,1.406 5.719,1.573 0.24,0.167 10 false 17 5.49,1.792 5.698,1.969 0.208,0.177 10 false 26 5.479,2.146 5.698,2.323 0.219,0.177 10 false 21 5.469,2.542 5.677,2.708 0.208,0.167 10 false 18 5.479,2.917 5.708,3.083 0.229,0.167 10 false 16 5.5,4.198 5.667,4.365 0.167,0.167 10 false 8 5.427,0.646 5.76,0.823 0.333,0.177 10 false F82 5.438,1.208 5.76,1.365 0.323,0.156 10 false B31 5.438,1.583 5.76,1.74 0.323,0.156 10 false B31 5.417,1.969 5.708,2.146 0.292,0.177 10 false B31 5.417,2.344 5.729,2.51 0.313,0.167 10 false F82 5.417,2.719 5.729,2.885 0.313,0.167 10 false B31 5.427,3.104 5.719,3.292 0.292,0.188 10 false B31 5.427,4.385 5.729,4.552 0.302,0.167 10 false F82

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (2 Range)
Shift SW Status (L Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
Shift SW Status (3 Range)
50003 234 147,125,126,131,132,127,128,130

f.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P and N

·

ON: Shift lever in P or N


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (P Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P

·

ON: Shift lever in P


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in R

·

ON: Shift lever in R


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (2 Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in 2

·

ON: Shift lever in 2


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (L Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in L

·

ON: Shift lever in L


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in N

·

ON: Shift lever in N


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (D Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in D and 3

·

ON: Shift lever in D or 3


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (3 Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in 3

·

ON: Shift lever in 3


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH)
a.
C193930C33
0.177,1 0.583,1.25 0.406,0.25 1.906,1.073 2.458,0.542 true 0.156,0.063 0.354,0.25 0.198,0.188 10 false *a 2.51,0.448 2.729,0.615 0.219,0.167 10 false RB 0.25,1.052 0.542,1.208 0.292,0.156 10 false B19
*a Front view of wire harness connector
(to Park/Neutral Position Switch)


Disconnect the park/neutral position switch connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B19-2 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
a.
C193930C34
0.177,1 0.583,1.25 0.406,0.25 2.292,1.083 2.698,0.625 true 0.156,0.063 0.354,0.25 0.198,0.188 10 false *a 2.75,0.542 2.969,0.708 0.219,0.167 10 false B 0.25,1.052 0.542,1.208 0.292,0.156 10 false B19
*a Front view of wire harness connector
(to Park/Neutral Position Switch)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B19-4 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH

NG

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH
a.
C283071C09
1.948,1 2.5,0.49 true 1.938,1 2.49,0.49 true 1.938,1 2.49,0.49 true 1.667,1.021 2.083,0.281 true 1.417,0.99 0.917,0.292 true 1.198,0.99 0.583,0.5 true 2.167,1.354 2.885,1.927 true 1.969,1.375 2.323,1.927 true 1.729,1.375 1.448,1.948 true 1.26,1.375 0.531,1.781 true 1.438,1.375 0.896,1.938 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 2.563,0.396 2.875,0.594 0.313,0.198 10 false RL 2.125,0.188 2.438,0.385 0.313,0.198 10 false RB 0.729,0.208 1.042,0.406 0.313,0.198 10 false 2L 0.448,0.406 0.76,0.604 0.313,0.198 10 false B 0.323,1.708 0.635,1.906 0.313,0.198 10 false NL 1.229,1.875 1.542,2.073 0.313,0.198 10 false DL 0.688,1.865 1,2.063 0.313,0.198 10 false LL 2.385,1.865 2.698,2.063 0.313,0.198 10 false PL 2.958,1.854 3.271,2.052 0.313,0.198 10 false L
*a Component without harness connected
(Park/Neutral Position Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P and N 10 kΩ or higher
2 (RB) - 6 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
1 (RL) - 2 (RB) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
2 (RB) - 9 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL) Shift lever in D or 3 Below 1 Ω
Shift lever not in D and 3 10 kΩ or higher
2 (RB) - 3 (2L) Shift lever in 2 Below 1 Ω
Shift lever not in 2 10 kΩ or higher
2 (RB) - 8 (LL) Shift lever in L Below 1 Ω
Shift lever not in L 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

NG

4.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.
C193928C27
0.125,0.031 0.302,0.198 0.177,0.167 10 false *a
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Disconnect the F19 transmission control switch (shift lock control unit assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Shift lever in 3 or 2 Below 1 Ω
Shift lever not in 3 and 2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY))

NG

REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY))
a.
C279782C06
0.125,0.865 0.615,1.177 0.49,0.313 0.26,0.948 0.719,1.146 0.458,0.198 10 false F19
*a Front view of wire harness connector
(to Transmission Control Switch (Shift Lock Control Unit Assembly))


Connect the B19 park/neutral position switch connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F19-1 - Body ground Ignition switch ON
Shift lever in D or 3
11 to 14 V
Ignition switch ON
Shift lever not in D and 3
Below 1 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY) - ECM)
a.

Connect the F19 transmission control switch (shift lock control unit assembly) connector.


b.

Turn the ignition switch to ON.


c.
C279787C06
1.615,0.333 2.031,0.583 0.417,0.25 2.198,1.656 1.969,0.896 true 2.177,1.698 2.333,1.896 0.156,0.198 10 false 3 1.698,0.375 2.156,0.573 0.458,0.198 10 false F82 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F82-8 (3) - Body ground Ignition switch ON
Shift lever in 3
11 to 14 V
Ignition switch ON
Shift lever not in 3
Below 1 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Turn the ignition switch to ON.


b.
C279777C16
1.083,0.333 1.5,0.583 0.417,0.25 1.667,0.333 2.083,0.583 0.417,0.25 2.167,3.333 2.563,2.615 true 1.094,3.229 1.417,2.646 true 1.021,3.24 0.771,2.677 true 0.948,3.24 0.385,2.698 true 0.438,3.615 0.948,3.333 true 0.427,3.875 0.958,3.417 true 1.156,0.375 1.615,0.573 0.458,0.198 10 false B31 1.74,0.385 2.198,0.583 0.458,0.198 10 false F82 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 2.625,2.51 2.781,2.708 0.156,0.198 10 false D 1.469,2.573 1.625,2.771 0.156,0.198 10 false L 0.292,3.813 0.448,4.01 0.156,0.198 10 false P 0.302,3.542 0.458,3.74 0.156,0.198 10 false N 0.646,2.583 0.802,2.781 0.156,0.198 10 false R 0.26,2.604 0.417,2.802 0.156,0.198 10 false 2
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B31-34 (P) - Body ground Ignition switch ON Shift lever in P 11 to 14 V
Ignition switch ON Shift lever not in P Below 1 V
B31-17 (R) - Body ground Ignition switch ON Shift lever R 11 to 14 V*
Ignition switch ON Shift lever not in R Below 1 V
B31-26 (N) - Body ground Ignition switch ON Shift lever in N 11 to 14 V
Ignition switch ON Shift lever not in N Below 1 V
F82-21 (D) - Body ground Ignition switch ON Shift lever in D or 3 11 to 14 V
Ignition switch ON Shift lever not in D and 3 Below 1 V
B31-18 (2) - Body ground Ignition switch ON Shift lever in 2 11 to 14 V
Ignition switch ON Shift lever not in 2 Below 1 V
B31-16 (L) - Body ground Ignition switch ON Shift lever in L 11 to 14 V
Ignition switch ON Shift lever not in L Below 1 V


HINT:

*: The voltage will drop slightly due to the back up light being turned on.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the F82 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F82-9 (NSW) - B19-4 (B) Always Below 1 Ω
B19-4 (B) or F82-9 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR