Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2013.08–2013.12
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Display Malfunction  


DESCRIPTION

OPERATION


The combination meter assembly uses the fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank assembly. The fuel sender gauge assembly has a variable resistor whose resistance changes according to the amount of fuel remaining. The gauge assemblies receive voltage from the combination meter assembly and change the voltage based on the resistance that changes according to the amount of fuel remaining in the fuel tank assembly. The combination meter assembly detects the voltage between each variable resistor and each resistor in the combination meter assembly, and operates the fuel receiver gauge.


FUEL RECEIVER GAUGE READING


a.

During normal driving:

As the fuel level in the fuel tank assembly rises and falls when driving on a hill or applying brakes, if the fuel sender gauge assembly output value were displayed as-is, the displayed value would fluctuate. For this reason, the averaged output value of the fuel sender gauge assembly is displayed.


b.

During refueling:

The fuel level in the fuel tank assembly rises rapidly when fuel is added. If the averaging process that is used during normal driving is used in this case, the fuel receiver gauge reading cannot be updated promptly. Therefore, when it is judged that fuel is being added to the vehicle based on the shift lever position and changes in the fuel level, output values from the fuel sender gauge assembly are immediately reflected in the fuel receiver gauge reading. This control is called refueling judgment.



REFUELING JUDGEMENT CONDITIONS


NOTICE:

Add fuel with the ignition switch off to ensure safety and to enable refueling judgment so that an appropriate fuel receiver gauge reading is obtained. If it is necessary to add fuel with the ignition switch ON, first move the shift lever to P or N*1, or apply the parking brake*2. Before driving the vehicle, wait until the fuel level indicated by the fuel receiver gauge stops rising (Approximately 1 minute from E to F).

*1: for Automatic Transaxle

*2: for Manual Transaxle



a.

Normal judgment condition (When normal refueling method is used)

With the ignition switch off, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.


b.

Other judgment conditions (When other refueling method is used)

Any of the following conditions is met:

·

With the vehicle and engine stopped and the ignition switch ON, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.

·

With the vehicle stopped, the engine running, the ignition switch ON and the shift lever in P or N, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level*1.

·

With the vehicle stopped, the engine running, the ignition switch ON and the shift lever in any driving position, the fuel sender gauge assembly detects a change of 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more in the fuel level*1.

·

The vehicle speed is 1.75 km/h (1.09 mph) or less (vehicle stopped) for 20 seconds or more continuously, and the fuel sender gauge assembly detects a change of 5 liters (5.3 US qts, 4.3 Imp. qts) or more in the fuel level*2.

*1: for Automatic Transaxle

*2: for Manual Transaxle





PRECAUTION FOR REFUELING


a.

The fuel sender gauge assembly cannot detect changes in fuel level within certain ranges (around points E and F). Therefore, even though 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more of fuel is added, refueling judgment may not be performed and the fuel receiver gauge reading may not change when fuel level is within such ranges.


b.

It takes approximately 1 minute for the fuel sender gauge assembly to change from E to F. If the vehicle is driven while the displayed fuel level is still rising, the fuel sender gauge assembly will be stopped at that point. The system will then return to normal operation mode, and the displayed fuel level will rise at a rate of approximately 1 minute/L (0.946 minutes/US qt, 1.14 minutes/Imp. qt) when the vehicle is being driven, or approximately 6 minutes/L (5.68 minutes/US qt, 6.82 minutes/Imp. qt) when the vehicle is stopped.



FORCED RESET OF FUEL RECEIVER GAUGE


When driving at 20 km/h (12 mph) or more, if the output values from the fuel sender gauge assembly are different from the fuel receiver gauge reading by 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more for approximately 2 minutes, output values from fuel sender gauge assembly are immediately reflected in the fuel receiver gauge reading to compensate for a situation when refueling judgment cannot be made.


WIRING DIAGRAM

E270884E08
2.052,0.917 2.667,1.115 0.615,0.198 10 false FS 2.302,0.917 2.469,1.188 0.167,0.271 10 false 2 2.052,2.25 2.667,2.448 0.615,0.198 10 false FE 2.323,2.25 2.49,2.521 0.167,0.271 10 false 3 5.49,0.917 6.104,1.115 0.615,0.198 10 false 37 5.479,2.25 6.094,2.448 0.615,0.198 10 false 36 5.719,0.917 6.333,1.115 0.615,0.198 10 false L 5.719,2.26 6.333,2.458 0.615,0.198 10 false E 0.417,3 1.031,3.198 0.615,0.198 10 false F28 0.417,3.156 3.917,3.354 3.5,0.198 10 false Fuel Suction Tube with Pump and Gauge Assembly 5.156,3.125 7.156,3.292 2,0.167 10 false Combination Meter Assembly 5.167,3 5.781,3.198 0.615,0.198 10 false F38 0.74,1.438 1.385,2.219 0.646,0.781 10 false Fuel Sender Gauge Assembly

CAUTION / NOTICE / HINT

HINT:

The fuel level warning light will come on when the fuel level is below 6.3 liters (6.7 US qts, 5.5 Imp. qts).


PROCEDURE

1.CHECK SYMPTOMS
a.

Ask the customer about the problem symptoms.


Result:
Result Proceed to
Malfunction occurs when adding fuel (Even after adding fuel, reading does not increase at all or increases very slowly, etc.). A
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom recurs). B
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom does not recur). C



A

2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)

B

12.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)

C

18.CHECK FOR DTC
2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full, Sender F -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Meter Operation
50004 122 3
OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY

3.CHECK FOR DTC
a.

Check if SFI system DTCs are output.


Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. (for 1NZ-FE with Automatic Transaxle) B
SFI system DTCs are output. (for 1NZ-FE with Manual Transaxle) C
SFI system DTCs are output. (for 2NZ-FE with Automatic Transaxle) D
SFI system DTCs are output. (for 2NZ-FE with Manual Transaxle) E



A

4.SYSTEM CHECK

B

C

D

E

4.SYSTEM CHECK
a.

Check the vehicle specifications.


Result:
Result Proceed to
w/ ABS A
w/o ABS B



A

5.CHECK FOR DTC

B

6.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL
5.CHECK FOR DTC
a.

Check if anti-lock brake system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Anti-lock brake system DTCs are not output. A
Anti-lock brake system DTCs are output. B



A

6.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL

B

6.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL
a.

Record the fuel receiver gauge reading.


b.

If the fuel tank assembly is almost full, drain 20 liters (21.1 US qts, 17.6 Imp. qts) or more of fuel. (This is not necessary when the fuel tank assembly is sufficiently below full.)


c.

Disconnect the cable from the negative (-) battery terminal to reset the fuel receiver gauge.

HINT:

Check that the ignition switch is turned off before disconnecting the cable from the negative (-) battery terminal.



d.

Connect the cable to the negative (-) battery terminal and turn the ignition switch to ON.


e.

Check that the fuel receiver gauge has been reset.


f.

Drive the vehicle at 1.75 km/h (1.09 mph) or more, then more the shift lever to P or N, or apply the parking brake, and turn the ignition switch off.


g.

Add 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more of fuel, turn the ignition switch to ON, and check that the fuel receiver gauge reading increases in proportion to the amount of fuel added.


Result:
Result Proceed to
Fuel receiver gauge reading increases in proportion to the amount of fuel added. A
Fuel receiver gauge reading does not change even when fuel is added. B



A

7.INSPECT FUEL TANK ASSEMBLY

B

8.READ VALUE USING GTS (FUEL INPUT)
7.INSPECT FUEL TANK ASSEMBLY
HINT:

Inspect the fuel tank assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of the fuel receiver gauge malfunction.


a.

Visually check the fuel tank assembly for any abnormalities.


b.

Check if there is an excessive amount of foreign matter in the fuel tank assembly.


c.

Check the installation condition of the fuel tank assembly and fuel sender gauge assembly.


Result:
Result Proceed to
Normal A
Appearance of the fuel tank assembly is abnormal. (for 1NZ-FE) B
Appearance of the fuel tank assembly is abnormal. (for 2NZ-FE) C
There is an excessive amount of foreign matter in the fuel tank assembly. D
The fuel tank assembly or fuel sender gauge assembly is not installed correctly. E



A

8.READ VALUE USING GTS (FUEL INPUT)

B

C

D

CLEAN INSIDE OF FUEL TANK ASSEMBLY

E

INSTALL FUEL TANK ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY CORRECTLY

8.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Data List.


e.

Check the values by referring to the table below.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0 L, Max.: 127.5 L Fuel receiver gauge indicates F: 37.6 L
Fuel receiver gauge indicates 1/2: 21.0 L
Fuel receiver gauge indicates E: 3.5 L
Unit: Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data displayed on the GTS is almost the same as the fuel receiver gauge indication. A
Fuel level data displayed on the GTS differs from the fuel receiver gauge indication. B



A

9.INSPECT FUEL SENDER GAUGE ASSEMBLY

B

REPLACE COMBINATION METER ASSEMBLY

9.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.


Result:
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

10.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

B

REPLACE FUEL SENDER GAUGE ASSEMBLY

C

REPLACE FUEL SENDER GAUGE ASSEMBLY

10.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
a.

Remove the fuel suction tube with pump and gauge assembly.



b.
E158805C04
1.292,1.313 0.688,1.313 true 1.833,1.219 2.427,0.625 true 0.219,0.104 0.979,0.292 0.76,0.188 10 false *a 2.51,0.542 2.76,0.708 0.25,0.167 10 false FS 0.458,1.229 0.708,1.396 0.25,0.167 10 false FE 0.615,0.656 1.406,0.823 0.792,0.167 10 false *b 0.615,3.094 1.406,3.26 0.792,0.167 10 false *c
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)
*b Connector A
*c Connector B


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 (FS) - B-2 Always Below 1 Ω
A-3 (FE) - B-1 Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)

B

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

C

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the F28 fuel suction tube with pump and gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-37 (L) - F28-2 (FS) Always Below 1 Ω
F38-37 (L) or F28-2 (FS) - Body ground Always 10 kΩ or higher
F38-36 (E) - F28-3 (FE) Always Below 1 Ω
F38-36 (E) or F28-3 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full, Sender F -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Meter Operation
50004 122 3
OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

13.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY

13.CHECK FOR DTC
a.

Check if SFI system DTCs are output.


Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. (for 1NZ-FE with Automatic Transaxle) B
SFI system DTCs are output. (for 1NZ-FE with Manual Transaxle) C
SFI system DTCs are output. (for 2NZ-FE with Automatic Transaxle) D
SFI system DTCs are output. (for 2NZ-FE with Manual Transaxle) E



A

14.SYSTEM CHECK

B

C

D

E

14.SYSTEM CHECK
a.

Check the vehicle specifications.


Result:
Result Proceed to
w/ ABS A
w/o ABS B



A

15.CHECK FOR DTC

B

16.CHECK FOR DTC
15.CHECK FOR DTC
a.

Check if anti-lock brake system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Anti-lock brake system DTCs are not output. A
Anti-lock brake system DTCs are output. B



A

16.CHECK FOR DTC

B

16.CHECK FOR DTC
a.

Check if meter / gauge system DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
DTC B1500 is not output. A
DTC B1500 is output. B



A

17.INSPECT FUEL RECEIVER GAUGE

B

17.INSPECT FUEL RECEIVER GAUGE
a.

Disconnect the cable from the negative (-) battery terminal to reset the fuel receiver gauge.

HINT:

Check that the ignition switch is turned off before disconnecting the cable from the negative (-) battery terminal.



b.

Connect the cable to the negative (-) battery terminal and turn the ignition switch to ON.


c.

Check if the fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank assembly.


Result:
Result Proceed to
Fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank assembly. A
Fuel receiver gauge reading does not correspond with the amount of fuel remaining in the fuel tank assembly. B



A

END

B

8.READ VALUE USING GTS (FUEL INPUT)
18.CHECK FOR DTC
a.

Check if SFI system DTCs are output.


Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. (for 1NZ-FE with Automatic Transaxle) B
SFI system DTCs are output. (for 1NZ-FE with Manual Transaxle) C
SFI system DTCs are output. (for 2NZ-FE with Automatic Transaxle) D
SFI system DTCs are output. (for 2NZ-FE with Manual Transaxle) E




A

19.SYSTEM CHECK

B

C

D

E

19.SYSTEM CHECK
a.

Check the vehicle specifications.


Result:
Result Proceed to
w/ ABS A
w/o ABS B



A

20.CHECK FOR DTC

B

21.INSPECT FUEL TANK ASSEMBLY
20.CHECK FOR DTC
a.

Check if anti-lock brake system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Anti-lock brake system DTCs are not output. A
Anti-lock brake system DTCs are output. B



A

21.INSPECT FUEL TANK ASSEMBLY

B

21.INSPECT FUEL TANK ASSEMBLY
HINT:

Inspect the fuel tank assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of the fuel receiver gauge malfunction.


a.

Visually check the fuel tank assembly for any abnormalities.


b.

Check if there is an excessive amount of foreign matter in the fuel tank assembly.


c.

Check the installation condition of the fuel tank assembly and fuel sender gauge assembly.


Result:
Result Proceed to
Normal A
Appearance of the fuel tank assembly is abnormal. (for 1NZ-FE) B
Appearance of the fuel tank assembly is abnormal. (for 2NZ-FE) C
There is an excessive amount of foreign matter in the fuel tank assembly. D
The fuel tank assembly or fuel sender gauge assembly is not installed correctly. E



A

REPLACE COMBINATION METER ASSEMBLY

B

C

D

CLEAN INSIDE OF FUEL TANK ASSEMBLY

E

INSTALL FUEL TANK ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY CORRECTLY