If the luggage compartment door entry unlock function does not operate, the request code may not be being transmitted from the luggage compartment door. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (luggage compartment)), a luggage door opening switch assembly".
The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the engine switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) or B27B0 is not output.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Trunk Open Mode | Luggage compartment door open mode | ON or OFF | Customization status displayed | - |
| Tester Display |
|---|
| Trunk Open Mode |
| Result | Proceed to |
|---|---|
| Entry luggage compartment door open mode is ON | A |
| Entry luggage compartment door open mode is OFF | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tr/B-Door Unlock SW | Luggage door opening switch assembly | ON or OFF | ON: Luggage door opening switch assembly pushed
OFF: Luggage door opening switch assembly not pushed |
·
Displays whether the luggage door opening switch assembly is on or off. ·
Use this Data List item to help determine if there is a switch malfunction when the luggage compartment door open function does not operate. |
| Tester Display |
|---|
| Tr/B-Door Unlock SW |
On the GTS screen, the display changes between ON and OFF according to the chart above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Approximately 0.3 m (0.984 ft.) |
Bring the electrical key transmitter sub-assembly near No. 3 indoor electrical key antenna assembly (luggage compartment), and perform an entry luggage compartment door open function check.
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication is not possible.
When pressing the luggage door opening switch assembly, hold the electrical key transmitter sub-assembly approximately 1 m (3.28 ft.) above the ground and approximately 0.3 m (0.984 ft.) away from the vehicle as shown in the illustration.
When the electrical key transmitter sub-assembly is brought near the No. 3 indoor electrical key antenna assembly (luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
| Result | Proceed to |
|---|---|
| Entry functions do not operate normally | A |
| Entry functions operate normally | B |
A
B
Check the following antennas in the key diagnostic mode.
| *a | 0.7 to 1.0 m (2.30 to 3.28 ft.) |
Select either channel 1 or channel 2 and inspect the key diagnostic mode for each channel.
When the electrical key transmitter sub-assembly is held at the same height as the rear bumper upper surface, align it with the center of the rear of the vehicle and check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle (0.7 to 1.0 m (2.30 to 3.28 ft.)). Make sure that the direction of the electrical key transmitter sub-assembly is as shown in the illustration.
If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer do not sounds | A |
| Wireless door lock buzzer sounds | B |
A
B
Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Disconnect the L4 No. 3 indoor electrical key antenna assembly (luggage compartment) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-8 (CLG8) - L4-1 (ANTE8) | Always | Below 1 Ω |
| F44-24 (CG8B) - L4-3 (CLGB) | Always | Below 1 Ω |
| F43-10 (E) - Body ground | Always | Below 1 Ω |
| F44-8 (CLG8) or L4-1 (ANTE8) - Body ground | Always | 10 kΩ or higher |
| F44-24 (CG8B) or L4-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F43 or F44 certification ECU (smart key ECU assembly) connectors.
Connect the L4 No. 3 indoor electrical key antenna assembly (luggage compartment) connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(No. 3 Indoor Electrical Key Antenna Assembly (Luggage Compartment)) |
*b | Waveform 1 |
| *c | luggage door opening switch assembly ON | - | - |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| L4-1 (ANTE8) - L4-3 (CLGB) | Procedure:
1.
Engine switch off 2.
All doors closed 3.
Press the luggage door opening switch assembly |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the luggage compartment door entry unlock functions operate normally.
Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (luggage compartment) before performing the inspection.
| Result | Proceed to |
|---|---|
| Entry unlock functions do not operate normally | A |
| Entry unlock functions operate normally | B |
A
B
Replace the certification ECU (smart key ECU assembly) with a new one.
Perform the registration procedures.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the luggage compartment door entry unlock functions operate normally.
| Result | Proceed to |
|---|---|
| Entry functions do not operate normally | A |
| Entry functions operate normally | B |
A
B
Remove the luggage compartment door lock assembly.
Click hereVehicle Interior>DOOR LOCK>LUGGAGE COMPARTMENT DOOR LOCK>REMOVAL
Inspect the luggage compartment door lock assembly.
Click hereVehicle Interior>DOOR LOCK>LUGGAGE COMPARTMENT DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Luggage compartment door lock motor:
Disconnect the 2O driver side junction block assembly connector.
Disconnect the L5 luggage compartment door lock assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2O-1 - L5-1 (ACT+) | Always | Below 1 Ω |
| L5-2 (ACT-) - Body ground | Always | Below 1 Ω |
| 2O-1 or L5-1 (ACT+) - Body ground | Always | 10 kΩ or higher |
Luggage door courtesy light switch:
Disconnect the 2N driver side junction block assembly connector.
Disconnect the L5 luggage compartment door lock assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2N-3 - L5-3 (D+) | Always | Below 1 Ω |
| L5-2 (ACT-) - Body ground | Always | Below 1 Ω |
| 2N-3 or L5-3 (D+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the driver side junction block assembly with a new or known good one.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check that the luggage compartment door entry unlock functions operate normally.
Luggage compartment door entry unlock functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the luggage door opening switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH>REMOVAL
Inspect the luggage door opening switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Disconnect the L1 luggage door opening switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-14 (TSW5) - L1-2 | Always | Below 1 Ω |
| L1-1 - Body ground | Always | Below 1 Ω |
| F43-14 (TSW5) or L1-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG