CHECK BODY COMPUTER AND DRIVER SIDE JUNCTION BLOCK ASSEMBLY
Disconnect the F52 body computer connector.
Remove the body computer from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *1 | Driver Side Junction Block Assembly | - | - |
| *1 | Body Computer | - | - |
Measure the resistance and voltage according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| MB-6 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| MB-7 (IG) - Body ground | - | Ignition power supply (IG signal) | Engine switch ON → OFF | 11 to 14 V → Below 1 V |
| MB-1 (GND) - Body ground | - | Ground | Always | Below 1 Ω |
| MB-18 (DCTY) - Body ground | - | Driver side door courtesy light switch input | Driver side door closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| F52-14 (PCTY) - Body ground | LG - Body ground | Front passenger side door courtesy light switch input | Front passenger side door closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| Rear door courtesy light switch LH input | Rear door LH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω | ||
| Rear door courtesy light switch RH input | Rear door RH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω | ||
| MB-20 (HCTY) - Body ground | - | Engine hood courtesy switch input | Engine hood open (OFF) → closed (ON) | 10 kΩ or higher → Below 1 Ω |
| MB-21 (LGCY) - Body ground | - | Luggage compartment door courtesy light switch input | Luggage compartment door closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Install the body computer to the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Reconnect the F52 body computer connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F52-15 (LSWD) - Body ground | W - Body ground | Driver side door unlock detection switch input | Driver side door unlocked | Below 1 V |
| Driver side door unlock detection switch input | Driver side door locked | Pulse generation | ||
| F52-6 (HAZ) - Body ground | P - Body ground | Hazard warning signal output | Theft deterrent system in alarm sounding state | Pulse generation
(Below 1 V ← → 11 to 14 V) |
| 2D-11 (SH) - Body ground | BR - Body ground | Security horn drive | Security horn sounding
(Theft deterrent system in alarm sounding state) |
Pulse generation
(Below 1 V ← → 11 to 14 V) |
| 2D-12 (HORN) - Body ground | LG - Body ground | Vehicle horn drive | Vehicle horns sounding
(Theft deterrent system in alarm sounding state) |
Pulse generation
(Below 1 V ← → 11 to 14 V) |
| 2J-4 (ACT-) - Body ground | V - Body ground | Door lock motor unlock drive output | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked | 11 to 14 V | |||
| 2J-3 (ACT+) - Body ground | GR - Body ground | Door lock motor lock drive output | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder locked | 11 to 14 V | |||
| F52-9 (PRG) - Body ground | BR - Body ground | Signal output to certification ECU (smart key ECU assembly) | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| F52-16 (RDA) - Body ground | GR - Body ground | Signal input from certification ECU (smart key ECU assembly) | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation |
If the result is not as specified, the body computer may be malfunctioning.
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Measure the resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F43-10 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F43-15 (IND) - F43-10 (E) | P - W-B | Security indicator illumination | Security indicator light illuminates
(It illuminates only for 27.5 seconds in alarm sounding state.) |
11 to 14 V |
| F44-13 (RDA3) - F43-10 (E) | GR - W-B | Signal output to body computer | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| F44-36 (PRG3) - F43-10 (E) | BR - W-B | Signal input from body computer | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation |
If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.