Home › Engine / Hybrid System › 2NZ-FE LUBRICATION › OIL PUMP › 2013.08–2014.03
RM30M0E _51 Engine / Hybrid System _017084 2NZ-FE LUBRICATION _0091245 OIL PUMP A

2NZ-FE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 3.REMOVE FRONT WHEEL RH

Hide 57533B 7.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 8.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 51441C 9.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51451A 10.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 51405A 11.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 27060 12.REMOVE GENERATOR WITH REGULATOR ASSEMBLY

Hide 12261 14.DISCONNECT VENTILATION HOSE

Hide 23820 15.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 11201 16.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12305 17.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

A245785C03
2.156,0.885 2.75,0.802 true 2.802,0.708 3.115,0.865 0.313,0.156 10 false *a
*a Wooden Block


a.

Place a wooden block on a jack underneath the engine assembly.


b.
A106618

Remove the 4 bolts, 2 nuts and engine mounting insulator sub-assembly RH from the engine mounting bracket RH and vehicle.


Hide 13407 18.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY

a.

Set the No. 1 cylinder to TDC/compression.

i.
A116203C02
2.146,1.042 2.406,1.948 true 2.26,1.01 2.688,1.927 true 2.365,1.979 2.531,2.156 0.167,0.177 10 false *a 2.656,1.969 2.823,2.146 0.167,0.177 10 false *b
*a Timing Notch
*b Timing Mark "0"


Turn the crankshaft damper sub-assembly, and align its timing notch with timing mark "0" of the oil pump assembly.


ii.
A116204C04
1.094,0.698 1.146,1.771 1.146,1.771 2.063,1.521 false 2.188,1.073 1.135,1.771 false 1,1.771 1.167,1.938 0.167,0.167 10 false *a
*a Timing Mark


Check that the timing marks on the camshaft timing sprocket and camshaft timing gear assembly are facing upward as shown in the illustration.

If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.



b.
A179644C01
1.802,2.094 0.917,2.469 0.917,2.469 1.979,1.698 true 0.667,1.156 0.719,1.583 0.719,1.583 0.396,1.406 false 3.01,2.885 3.323,3.042 0.313,0.156 10 false *a 1.177,3.229 1.49,3.385 0.313,0.156 10 false *b 0.625,2.406 1.135,2.625 0.51,0.219 10 false SST 0.771,1.531 1.281,1.75 0.51,0.219 10 false SST
*a Hold
*b Turn


Using SST, loosen the bolt of the crankshaft damper sub-assembly.

SST
09213-14010  (91651-60865)
09330-00021  (09330-00030)

NOTICE:

Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.



c.

Remove SST from the crankshaft damper sub-assembly.


d.

Remove the bolt and crankshaft damper sub-assembly from the crankshaft.


Hide 15100Q 19.REMOVE CRANKSHAFT POSITION SENSOR

Hide 11101J 20.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 16173 21.REMOVE WATER PUMP PULLEY

Hide 16100 22.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 12315A 23.REMOVE ENGINE MOUNTING BRACKET RH

A116553

a.

Remove the 4 bolts and engine mounting bracket RH from the oil pump assembly.


Hide 15100 24.REMOVE OIL PUMP ASSEMBLY

A278964

a.

Remove the 15 bolts, nut and 2 wire harness clamp brackets from the oil pump assembly.


b.
A116555C02
3.042,0.927 2.635,1.531 true 3.01,0.771 3.177,0.927 0.167,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the oil pump assembly by prying between the oil pump assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.

NOTICE:

Do not damage the contact surfaces of the oil pump assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.



c.
A116556

Remove the 2 O-rings from the cylinder block sub-assembly and oil pan sub-assembly.


Hide 25.REMOVE TAPER SCREW PLUG

a.
G100163

Using an 8 mm hexagon wrench, remove the taper screw plug from the oil pump assembly.


Hide 15100C 26.REMOVE OIL PUMP SEAL

a.
A301961C01
1.615,0.813 2.063,0.167 true 0.542,1.115 0.333,0.323 0.333,0.323 1.313,0.365 false 0.104,0.219 0.417,0.375 0.313,0.156 10 false *a 2.146,0.083 2.458,0.24 0.313,0.156 10 false *b
*a Wooden Block
*b Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the oil pump seal from the oil pump assembly.