CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY COMPUTER
Remove the body computer from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *1 | Driver Side Junction Block Assembly | - | - |
| *1 | Body Computer | - | - |
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| MB-1 (GND) - Body ground | - | Ground | Always | Below 1 Ω |
| MB-6 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| MB-7 (IG) - Body ground | - | Engine switch power supply | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Install the body computer to the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 2J-3 (ACT+) - Body ground | GR - Body ground | Door lock motor lock drive output (front door) | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder locked | 11 to 14 V | |||
| 2J-4 (ACT-) - Body ground | V - Body ground | Door lock motor unlock drive output (all door) | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked | 11 to 14 V | |||
| 2O-2 (ACT+) - Body ground | BE - Body ground | Door lock motor lock drive output (rear door) | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder locked | 11 to 14 V | |||
| 2N-1 (DCTY) - Body ground | BR - Body ground | Front door courtesy light switch LH input*1 | Front door LH open | Below 1 V |
| Front door LH closed | Pulse generation | |||
| Front door courtesy light switch RH input*2 | Front door RH open | Below 1 V | ||
| Front door RH closed | Pulse generation | |||
| 2N-3 (LGCY) - Body ground | R - Body ground | Luggage compartment door courtesy light switch input | Luggage compartment door open | Below 1 V |
| Luggage compartment door closed | Pulse generation | |||
| 2O-1 (TR+) - Body ground | L - Body ground | Door lock motor lock drive output (Luggage compartment door) | Luggage compartment door closed | Below 1 V |
| Luggage compartment door open switch pressed | 11 to 14 V | |||
| F52-6 (HAZ) - Body ground | P - Body ground | Hazard warning signal output | Answer-back off | 11 to 14 V |
| Answer-back on | Below 1 V | |||
| F52-9 (PRG) - Body ground | BR - Body ground | Signal output to certification ECU (smart key ECU assembly) | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| F52-14 (PCTY) - Body ground | LG - Body ground | Except front door courtesy light switch LH input*1 | Except front door LH open | Below 1 V |
| Except front door LH closed | Pulse generation | |||
| Except front door courtesy light switch RH input*2 | Except front door RH open | Below 1 V | ||
| Except front door RH closed | Pulse generation | |||
| F52-15 (LSWD) - Body ground | L - Body ground*1 | Front door LH unlock detection switch input | Front door LH unlocked | Below 1 V |
| Front door LH locked | Pulse generation | |||
| W - Body ground*2 | Front door RH unlock detection switch input | Front door RH unlocked | Below 1 V | |
| Front door RH locked | Pulse generation | |||
| F52-16 (RDA) - Body ground | GR - Body ground | Signal input from certification ECU (smart key ECU assembly) | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation |
*1: for LHD
*2: for RHD
If the result is not as specified, the body computer or driver side junction block assembly may be malfunctioning.
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F43-1 (+B) - Body ground | B - Body ground | Battery power supply | Always | 11 to 14 V |
| F43-10 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| F44-33 (CUTB) - Body ground | L - Body ground | Dark current cut fuse pin input signal | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F43-2 (BZR) - Body ground | G - Body ground | Wireless door lock buzzer signal | Wireless door lock buzzer off | Below 1 V |
| Wireless door lock buzzer on | Pulse generation | |||
| F44-3 (RCO) - F43-10 (E) | GR - W-B | Wireless tuner power supply output circuit | Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed | 4.5 to 5.5 V pulse generation at regular intervals → 4.5 to 5.5 V |
| F43-9 (LSWP) - F43-10 (E) | W - W-B | Except front door LH unlock detection switch input*1 | Engine switch off, all doors closed, all doors unlocked and electrical key transmitter sub-assembly lock switch not pressed | Below 1 V |
| Engine switch off, all doors closed, all doors unlocked and electrical key transmitter sub-assembly lock switch pressed | 8.5 V or higher | |||
| Except front door RH unlock detection switch input*2 | Engine switch off, all doors closed, all doors unlocked and electrical key transmitter sub-assembly lock switch not pressed | Below 1 V | ||
| Engine switch off, all doors closed, all doors unlocked and electrical key transmitter sub-assembly lock switch pressed | 8.5 V or higher | |||
| F44-13 (RDA3) - F43-10 (E) | GR - W-B | Signal output to body computer | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| F44-21 (CSEL) - F43-10 (E) | P - W-B | Communication channel switching circuit | Engine switch off and all doors closed | Pulse generation |
| F44-22 (RDAS) - F43-10 (E) | LG - W-B | RF Signal input circuit | Engine switch off, all doors closed, all doors locked and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed | 11 to 14 V → Pulse generation |
| F44-36 (PRG3) - F43-10 (E) | BR - W-B | Signal input from body computer | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation |
*1: for LHD
*2: for RHD
If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.
CHECK DOOR CONTROL RECEIVER
Disconnect the F46 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F46-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the F46 door control receiver connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F46-2 (CSEL) - F46-1 (GND) | P - W-B | Communication channel switching circuit | Engine switch off and all doors closed | Pulse generation |
| F46-4 (+5) - F46-1 (GND) | GR - W-B | Battery (power supply) | Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed | 4.5 to 5.5 V pulse generation at regular intervals → 4.5 to 5.5 V |
| F46-5 (DATA) - F46-1 (GND) | LG - W-B | Data output | Engine switch off, all doors closed, all doors locked and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed | 11 to 14 V → Pulse generation |
If the result is not as specified, the door control receiver may be malfunctioning.