CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY COMPUTER
Remove the body computer from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *1 | Driver Side Junction Block Assembly | - | - |
| *1 | Body Computer | - | - |
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| MB-1 (GND) - Body ground | - | Ground | Always | Below 1 Ω |
| MB-6 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| MB-7 (IG) - Body ground | - | Ignition switch power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Install the body computer to the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulse according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 2J-3 (ACT+) - Body ground | GR - Body ground | Door lock motor lock drive output (front door) | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder locked | 11 to 14 V | |||
| 2J-4 (ACT-) - Body ground | V - Body ground | Door lock motor unlock drive output (all door) | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked | 11 to 14 V | |||
| 2O-2 (ACT+) - Body ground | BE - Body ground | Door lock motor lock drive output (rear door) | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder locked | 11 to 14 V | |||
| 2N-1 (DCTY) - Body ground | BR - Body ground | Front door courtesy light switch LH input*1 | Front door LH open | Below 1 V |
| Front door LH closed | Pulse generation | |||
| Front door courtesy light switch RH input*2 | Front door RH open | Below 1 V | ||
| Front door RH closed | Pulse generation | |||
| F52-6 (HAZ) - Body ground | P - Body ground | Hazard warning signal output | Answer-back off | 11 to 14 V |
| Answer-back on | Below 1 V | |||
| F52-8 (KSW) - Body ground | SB - Body ground | Unlock warning switch input | No key in ignition key cylinder | Pulse generation |
| Key in ignition key cylinder | Below 1 V | |||
| F52-9 (PRG) - Body ground | BR - Body ground | Signal output to door control receiver | Key inserted into ignition key cylinder → Key pulled out of ignition key cylinder | 11 to 14 V → Pulse generation → 11 to 14 V |
| F52-14 (PCTY) - Body ground | LG - Body ground | Except front door courtesy light switch LH input*1 | Except front door LH open | Below 1 V |
| Except front door LH closed | Pulse generation | |||
| Except front door courtesy light switch RH input*2 | Except front door RH open | Below 1 V | ||
| Except front door RH closed | Pulse generation | |||
| F52-15 (LSWD) - Body ground | L - Body ground*1 | Front door LH unlock detection switch input | Front door LH unlocked | Below 1 V |
| Front door LH locked | Pulse generation | |||
| W - Body ground*2 | Front door RH unlock detection switch input | Front door RH unlocked | Below 1 V | |
| Front door RH locked | Pulse generation | |||
| F52-16 (RDA) - Body ground | G - Body ground | Signal input from door control receiver | Ignition switch off, all doors closed and door control transmitter assembly switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed and door control transmitter assembly switch pressed | Pulse generation |
*1: for LHD
*2: for RHD
If the result is not as specified, the body computer or driver side junction block assembly may be malfunctioning.
CHECK DOOR CONTROL RECEIVER
Disconnect the door control receiver connector.
Measure the resistance and voltage according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F47-5 (+B) - Body ground | L - Body ground | Battery (power supply) | Always | 11 to 14 V |
| F47-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the F47 door control receiver connector.
Measure the voltage and check for pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F47-2 (RDA) - F47-1 (GND) | G - W-B | Signal output to body computer | Ignition switch off, all doors closed and door control transmitter assembly switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed and door control transmitter assembly switch pressed | Pulse generation | |||
| F47-3 (PRG) - F47-1 (GND) | BR - W-B | Signal input from body computer | Key inserted into ignition key cylinder → Key pulled out of ignition key cylinder | 11 to 14 V → Pulse generation → 11 to 14 V |
If the result is not as specified, the door control receiver may be malfunctioning.