64811
1.CLEAN BACK WINDOW GLASS
Using a scraper, remove any back window glass adhesive dam and adhesive residue from the back window glass.
Be careful not to damage the back window glass.
Clean the outer circumference of the back window glass with a non-residue solvent.
Do not touch the back window glass surface after cleaning it.
Be careful not to damage the back window glass.
Even if using new back window glass, clean it with a non-residue solvent.
2. CLEAN VEHICLE BODY
| *a | Adhesive |
| *b | Vehicle Body |
Clean and shape the contact surface of the vehicle body.
Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
Be careful not to damage the vehicle body.
Leave as much adhesive on the vehicle body as possible.
Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.
Even if all the adhesive has been removed, clean the vehicle body.
56116D
3.INSTALL NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)
Using a brush or sponge, coat the application area of 2 new No. 2 back window glass stoppers with primer G.
Do not apply too much primer G.
Allow the primer G coating to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
Install the 2 No. 2 back window glass stoppers onto the back window glass as shown in the illustration.
| *a | Back Side | - | - |
| Area | Dimension | Area | Dimension |
|---|---|---|---|
| a | 40.0 mm (1.57 in.) | b | 14.2 to 15.2 mm (0.560 to 0.598 in.) |
Only 2-piece type No. 2 back window glass stoppers are supplied. Use the 2-piece type back window glass stoppers even if a 1-piece type was used.
56115B
4.INSTALL NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)
| *1 | No. 1 Back Window Glass Stopper |
Install 2 new No. 1 back window glass stoppers to the vehicle body as shown in the illustration.
Only 2-piece type back window glass stoppers are provided as supply parts. Use 2-piece type back window glass stoppers as replacements even if a 1-piece type was originally installed.
64813D
5.INSTALL BACK WINDOW GLASS ADHESIVE DAM
Using a brush or sponge, coat the application area of a new back window glass adhesive dam with primer G.
Do not apply too much primer G.
Allow the primer G coating to dry for 3 minutes or more.
Do not keep any of the opened primer G for later use.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
Install the back window adhesive dam, applying double-sided tape all the way around the back window glass except where the dam is installed as shown in the illustration.
| *1 | Back Window Glass Adhesive Dam | - | - |
| *a | Back Side | *b | Ceramic Notch |
| Area | Dimension | Area | Dimension |
|---|---|---|---|
| a | 6.6 mm (0.260 in.) | b | 9.0 mm (0.354 in.) |
64811
6.INSTALL BACK WINDOW GLASS
| *a | Matchmarks |
Position the back window glass.
Using suction cups, place the back window glass in the correct position.
Check that the whole contact surface of the back window glass rim is perfectly even.
Align the matchmarks on the back window glass and vehicle body.
Check that the back window glass stoppers are attached to the vehicle body correctly.
Remove the back window glass.
| *a | Primer M |
| *b | Adhesive |
| *c | Correct |
| *d | Incorrect |
Using a brush, coat the installation surface on the vehicle body with primer M.
Do not coat the adhesive with primer M.
Do not apply too much primer M.
Allow the primer coating to dry for 3 minutes or more.
Do not keep any of the opened primer M for later use.
Using a brush or sponge, coat the adhesive application area with primer G.
| *a | Back Side | *b | Primer G |
| Area | Dimension | Area | Dimension |
|---|---|---|---|
| a | 11.0 mm (0.433 in.) or more | b | 10.0 mm (0.394 in.) or more |
| c | 19.0 mm (0.748 in.) or more | - | - |
Do not apply too much primer G.
Allow the primer G coating to dry for 3 minutes or more.
Do not keep any of the opened primer G for later use.
Apply primer G onto the ceramic notches.
If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.
Apply adhesive to the back window glass.
Toyota Genuine Windshield Glass Adhesive or equivalent
| *a | Nozzle |
| *b | Adhesive |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Dimension |
|---|---|
| A | 12.0 mm (0.472 in.) |
| B | 8.0 mm (0.315 in.) |
After cutting off the tip, use all adhesive within the time described in the table below.
| Temperature | Usage Time Frame |
|---|---|
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour and 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the back window glass as shown in the illustration.
| *a | Back Side | *b | Adhesive |
| Area | Dimension | Area | Dimension |
|---|---|---|---|
| a | 14.7 mm (0.579 in.) | b | 10.0 mm (0.394 in.) |
| c | 14.8 mm (0.583 in.) | d | 8.0 mm (0.315 in.) |
| e | 17.1 mm (0.673 in.) | - | - |
Install the back window glass.
| *a | Matchmarks |
Using suction cups, position the back window glass so that the matchmarks are aligned, and press it in gently along the rim.
Check that the back window glass stoppers are attached to the vehicle body correctly.
Check the clearance between the vehicle body and back window glass.
Lightly press the front surface of the back window glass to ensure a close fit.
Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Hold the back window glass using protective tape until the applied adhesive becomes hard.
Do not drive the vehicle for the time described in the table below.
| Temperature | Minimum Time Prior to Driving Vehicle |
|---|---|
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
Connect each connector.
Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.
7.INSPECT FOR LEAK AND REPAIR
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
63310
8.INSTALL ROOF HEADLINING ASSEMBLY
Return the rear section of the roof headlining assembly to its original position.
74610A
9.INSTALL ASSIST GRIP SUB-ASSEMBLY
63339A
10.INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/ Cover)
64330D
11.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
62472A
12.INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH
62471A
13.INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH
Use the same procedure as for the LH side.
62552F
14.INSTALL REAR SEAT SIDE GARNISH LH
62551F
15.INSTALL REAR SEAT SIDE GARNISH RH
Use the same procedure as for the LH side.
73370
16.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
73360
17.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62332A
18.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Install the rear door opening trim weatherstrip LH.
62331A
19.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
20.INSTALL REAR SEAT ASSEMBLY (for Fixed Seat Type)
21.INSTALL REAR SEAT ASSEMBLY (for Separate Seat Type)
81570
22.INSTALL CENTER STOP LIGHT ASSEMBLY