The theft deterrent system is unset when the IG signal and engine speed signal are input to the body computer for 2 seconds or more continuously.
The engine speed signal is sent from the ECM to the body computer or certification ECU (smart key ECU assembly). For this reason, if there is an abnormality in an ECU or wire harness, the system may not function correctly.
Before replacing the certification ECU (smart key ECU assembly) or ECM, refer to Service Bulletin.
Inspect the fuses for circuits related to this system before performing the following procedure.
Disconnect the driver side junction block assembly connectors.
Measure the voltage according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Driver Side Junction Block Assembly) |
- | - |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 2A-1 - Body ground | Always | 11 to 14 V |
| 2F-1 - Body ground | Engine switch on (IG) | 11 to 14 V |
| 2F-1 - Body ground | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the body computer.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Disconnect the driver side junction block assembly connectors.
Measure the resistance according the value(s) in the table below.
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2A-1 - MB-6 (BECU) | Always | Below 1 Ω |
| 2F-1 - MB-7 (IG) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the body computer to the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Reconnect the body computer connector.
Reconnect the 2A and 2F driver side junction block assembly connectors.
Remove the driver side junction block assembly with connectors still connected.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component with harness connected
(Body Computer) |
Check the engine speed input signal waveform at the terminal of body computer.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F52-13 (TACH) - Body ground | Engine stopped | Not pulse generation |
| F52-13 (TACH) - Body ground | Engine running | Pulse generation |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the F52 body computer connector.
Disconnect the B32 ECM connector.
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F52-13 (TACH) - B32-16 (NEO) | Always | Below 1 Ω |
| F52-13 (TACH) - F43-6 (NE) | Always | Below 1 Ω |
| B32-16 (NEO) - F43-6 (NE) | Always | Below 1 Ω |
| F52-13 (TACH) or B32-16 (NEO) - Body ground | Always | 10 kΩ or higher |
| F52-13 (TACH) or F43-6 (NE) - Body ground | Always | 10 kΩ or higher |
| B32-16 (NEO) or F43-6 (NE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F52 body computer connector.
Reconnect the B32 ECM connector.
Reconnect the F43 certification ECU (smart key ECU assembly) connector.
| *a | Component with harness connected
(ECM) |
Check the engine speed input signal waveform at the terminal of ECM.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B32-16 (NEO) - Body ground | Engine stopped | Not pulse generation |
| B32-16 (NEO) - Body ground | Engine running | Pulse generation |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the F52 body computer connector.
Disconnect the ECM connector.
| *a | Front view of wire harness connector
(to ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B32-16 (NEO) - Body ground | Engine stopped | 11 to 14 V |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the F52 body computer connector.
Reconnect the B32 ECM connector.
Reconnect the F43 certification ECU (smart key ECU assembly) connector.
| *a | Component with harness connected
(ECM) |
Check the engine speed input signal waveform at the terminal of ECM.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B32-16 (NEO) - Body ground | Engine stopped | Not pulse generation |
| B32-16 (NEO) - Body ground | Engine running | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
OK
NG