Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE(for 2NZ-FE) › 2013.08–2014.03
RM30M0E _52 Drivetrain _017091 C54 MANUAL TRANSMISSION / TRANSAXLE _0094350 TRANSMISSION CONTROL CABLE(for 2NZ-FE) A

C54 MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE(for 2NZ-FE)  INSTALLATION  


PROCEDURE

Hide 33829 1.INSTALL TRANSMISSION CONTROL CABLE SUPPORT

HINT:

Perform this procedure only when replacement of the transmission control cable support is necessary.


a.
C282053C01
0.802,1.438 1.135,1.219 true 1.406,0.844 1.573,0.75 true 0.646,1.344 0.958,1.5 0.313,0.156 10 false *a 1.615,0.635 1.927,0.792 0.313,0.156 10 false *b
*a Arrow Mark
*b Detent


Install the transmission control cable support to the body with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:
·

Install the transmission control cable support so that its arrow mark points to the front of the vehicle.

·

Make sure that the detent of the transmission control cable support is pushing against the dash silencer.




Hide 33820B 2.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Install the transmission control cable assembly to the body with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
C283113C01
2.188,0.406 3.031,0.656 3.031,0.656 2.552,0.708 true 0.177,0.875 0.313,1.052 0.135,0.177 10 true A 2.063,1.583 2.198,1.76 0.135,0.177 10 true A 1.667,0.01 1.802,0.188 0.135,0.177 10 true B 2.771,1.063 2.906,1.24 0.135,0.177 10 true B 3.063,0.573 3.375,0.729 0.313,0.156 10 false *a
*a Paint Mark


Install the transmission control cable assembly to the control cable bracket with 2 new clips B.

NOTICE:

Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the control cable bracket before installing the clips.



c.

Connect the transmission control cable assembly to the floor shift selecting bellcrank assembly with the 2 washers and 2 clips A.


d.
C288539C01
2.24,0.906 2.552,0.708 false 1,1.875 1.313,1.677 false 0.854,1.781 1.167,1.938 0.313,0.156 10 false *1 2.594,0.604 2.906,0.76 0.313,0.156 10 false *2
*1 Nut
*2 Lock
V100135

Rotate approximately 180°
V100136

Push in


Rotate the 2 nuts of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut, push in the lock.

NOTICE:

Do not rotate the nut excessively as it may damage the internal spring and the transmission control cable assembly will not be reusable.



e.
C283111C02
1.281,3.729 0.938,3.542 false 0.813,0.615 0.531,0.417 false 2.646,0.604 2.365,0.406 false 2.156,3.604 2,3.719 false 2.854,3.396 2.698,2.771 true 2.167,3.5 2.396,3.698 0.229,0.198 10 false *1 2.813,3.417 3.01,3.583 0.198,0.167 10 false *2 0.375,0.323 0.688,0.479 0.313,0.156 10 false *a 2.219,0.323 2.531,0.479 0.313,0.156 10 false *3 0.313,0.573 0.469,0.771 0.156,0.198 10 false A 1.25,0.573 1.406,0.771 0.156,0.198 10 false A 0.792,3.448 1.104,3.604 0.313,0.156 10 false *a
*1 Clip A
*2 Clip B
*3 Lock
*a Protrusion


Install the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:
·

Install the transmission control cable assembly with the protrusion of the cable outer facing upwards.

·

After installation, make sure that the lock is projecting from A as shown in the illustration.




f.

Engage the clip B and connect the shift cable end of the transmission control cable assembly to the floor shift shift lever assembly.


g.

Connect the select cable end of the transmission control cable assembly to the floor shift shift lever assembly with the clip A.

NOTICE:
·

Install the transmission control cable assembly with the protrusion of the select cable end facing upwards.

·

Perform the installation with the clip A at the correct direction as shown in the illustration.




Hide 58151 3.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the body with the 2 bolts and nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17410 4.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 5.INSTALL FRONT FLOOR CENTER BRACE

Hide 74410 7.INSTALL BATTERY CARRIER ASSEMBLY

Hide 10.INSPECT FOR EXHAUST GAS LEAK