Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET › 2013.08–2014.03
RM30M0E _51 Engine / Hybrid System _017074 2NZ-FE ENGINE MECHANICAL _0091014 CYLINDER HEAD GASKET A

2NZ-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


PROCEDURE

Hide 11101A 1.INSPECT CYLINDER HEAD SET BOLT

Hide 11115 2.INSTALL CYLINDER HEAD GASKET

a.

Clean and degrease the lower surface of the cylinder head sub-assembly and upper surface of the cylinder block sub-assembly.


b.
A302801C01
0.479,1.927 0.708,1.927 false 0.531,0.708 0.719,0.542 false 0.51,1.677 0.75,1.792 false 2.865,1.104 3.01,1.281 false 3.01,1.313 3.323,1.469 0.313,0.156 10 false *1 0.375,1.573 0.688,1.729 0.313,0.156 10 false *2 0.375,0.698 0.688,0.854 0.313,0.156 10 false *a 0.292,1.865 0.604,2.021 0.313,0.156 10 false *b 0.385,0.094 0.542,0.292 0.156,0.198 10 false A 1.063,0.094 1.219,0.292 0.156,0.198 10 false A 2.042,0.594 2.333,0.76 0.292,0.167 10 false A-A 1.844,1.49 2.865,1.677 1.021,0.188 10 false φ4.5 to 5.5 mm 1.885,1.677 3.104,1.844 1.219,0.167 10 false (0.177 to 0.217 in.)
*1 Cylinder Head Gasket
*2 No. 1 Chain Vibration Damper
*a Apply enough seal packing so that it will spread to the inner side
*b Apply enough seal packing so that it will spread onto the No. 1 Chain Vibration Damper
V100145

Seal Packing Black


Apply seal packing to a new cylinder head gasket in the locations shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:

Install the cylinder head sub-assembly within 3 minutes and tighten the cylinder head set bolts within 15 minutes of applying seal packing.



c.
A287618C02
0.958,0.063 1.271,0.26 0.313,0.198 10 *a
*a Lot No.
V100136

Engine Front


Place the cylinder head gasket on the cylinder block sub-assembly with the Lot No. stamp facing upward.

NOTICE:
·

Be sure to place the cylinder head gasket in the correct direction.

·

Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the cylinder head gasket.

·

After installing the cylinder head sub-assembly, wipe off any excess seal packing that seeped out.




Hide 11101 3.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:

The cylinder head set bolts are tightened in 2 successive steps.


a.

Apply a light coat of engine oil to the threads of the 10 cylinder head set bolts.


b.
A133597E03
2.177,1.75 2.333,1.948 0.156,0.198 10 false 3 2.188,0.115 2.344,0.313 0.156,0.198 10 false 5 0.573,1.74 0.813,1.948 0.24,0.208 10 false 10 0.625,0.104 0.865,0.313 0.24,0.208 10 false 8 1.135,0.104 1.375,0.313 0.24,0.208 10 true 4 2.677,1.719 2.833,1.917 0.156,0.198 10 true 7 2.698,0.115 2.854,0.313 0.156,0.198 10 false 9 1.646,0.115 1.802,0.313 0.156,0.198 10 false 2 1.125,1.729 1.281,1.927 0.156,0.198 10 false 6 1.667,1.74 1.823,1.938 0.156,0.198 10 false 1

Using several steps, install and tighten the 10 cylinder head set bolts and 10 plate washers uniformly with an 8 mm bi-hexagon wrench, in the sequence shown in the illustration.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


c.
A133600C01
1.552,1.333 1.667,1.104 true 1.396,1.354 1.563,1.51 0.167,0.156 10 false *a 1.042,0.302 1.344,0.51 0.302,0.208 10 false 90° 2.729,0.271 3.031,0.479 0.302,0.208 10 false 90°
*a Paint Mark
V100135

Engine Front


Mark the front of the cylinder head set bolt with paint.


d.

Retighten the cylinder head set bolts 90° and then an additional by 90° as shown in the illustration.


e.

Check that the paint mark is now at a 180° angle from the engine front.


f.

Wipe off any excess seal packing that seeped out.


Hide 13506 6.INSTALL CHAIN SUB-ASSEMBLY

Hide 13559 7.INSTALL CHAIN TENSIONER SLIPPER

Hide 13540 8.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 15100C 9.INSTALL OIL PUMP SEAL

Hide 15100 10.INSTALL OIL PUMP ASSEMBLY

Hide 12315A 11.INSTALL ENGINE MOUNTING BRACKET RH

Hide 16100 12.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 16173 13.INSTALL WATER PUMP PULLEY

Hide 11101J 14.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 15100Q 15.INSTALL CRANKSHAFT POSITION SENSOR

Hide 13407 16.INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY

Hide 12305 17.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

Hide 11201 18.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 25591 20.INSTALL MANIFOLD SUPPORT BRACKET

Hide 82121 21.CONNECT ENGINE WIRE

a.

Connect the engine wire to the cylinder head sub-assembly.


b.

Connect the engine wire to the cylinder head sub-assembly with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 16268 23.INSTALL NO. 1 WATER BY-PASS PIPE

Hide 11452 25.INSTALL OIL LEVEL DIPSTICK GUIDE

a.

Apply engine oil to a new O-ring.


b.

Install the O-ring to the oil level dipstick guide.

NOTICE:

Do not twist the O-ring.



c.

Install the oil level dipstick guide to the cylinder block sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Engage the clamp to connect the engine wire to the oil level dipstick guide.


Hide 17111 26.INSTALL INTAKE MANIFOLD WITH THROTTLE BODY WITH MOTOR ASSEMBLY

a.

Install a new intake manifold to head gasket to the intake manifold.


b.

Install the intake manifold with throttle body with motor assembly to the cylinder head sub-assembly with the 3 bolts and 2 nuts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


c.

Engage the 3 clamps to install the engine wire to the 3 wire harness clamp brackets.


d.

Connect the throttle body with motor assembly connector.


e.

Engage the 2 clamps to connect the engine wire to the 2 wire harness clamp brackets.


f.

Connect the water by-pass hose to the throttle body with motor assembly with the hose clip.


g.

Connect the No. 2 water by-pass hose to the throttle body with motor assembly with the hose clip.


h.

Engage the clamp to connect the No. 2 water by-pass hose to the hose clamp.


Hide 15301 27.INSTALL OIL LEVEL DIPSTICK SUB-ASSEMBLY

Hide 44774 28.CONNECT UNION TO CONNECTOR TUBE HOSE

a.

Connect the union to connector tube hose to the intake manifold with the hose clip.


Hide 32.CONNECT RADIATOR RESERVOIR TANK HOSE

Hide 23901 35.CONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23842A 36.INSTALL EFI FUEL PIPE CLAMP

Hide 28800 39.INSTALL BATTERY

a.
A300619C01
0.615,1.521 0.781,1.688 true 0.448,1.563 0.365,1.719 true 0.823,1.646 1.01,1.813 0.188,0.167 10 false *1 0.25,1.729 0.563,1.885 0.313,0.156 10 false *2
*1 Battery Clamp Bolt
*2 Battery Carrier Assembly


Install the battery to the battery tray.


b.

Install the battery clamp sub-assembly to the battery carrier assembly with the 2 nuts and battery clamp bolt.

HINT:

Engage the hook of the battery clamp bolt to the notch of the battery carrier assembly.


Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


c.

Connect the positive (+) battery terminal to the battery with the nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


d.

Install the terminal cover to the positive (+) battery terminal.


Hide 17735 41.INSTALL AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE

Hide 17341T 42.CONNECT NO. 1 AIR HOSE (for Automatic Transaxle)

Hide 23827A 43.CONNECT NO. 2 FUEL VAPOR FEED HOSE

Hide 23820 44.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 27060 45.INSTALL GENERATOR WITH REGULATOR ASSEMBLY

Hide 17410 46.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 47.INSTALL FRONT FLOOR CENTER BRACE

Hide 55781E 49.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 50.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 51.INSTALL FRONT WHEEL RH

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 58.INSPECT FOR EXHAUST GAS LEAK

Hide 51441C 63.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51442C 64.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51405A 65.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 66.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)