Home › Engine / Hybrid System › 1NZ-FE FUEL › FUEL TANK(for TMMIN Made) › 2013.12–2016.10
RM30M0E _51 Engine / Hybrid System _017075 1NZ-FE FUEL _0106428 FUEL TANK(for TMMIN Made) A

1NZ-FE FUEL  FUEL TANK(for TMMIN Made)  INSTALLATION  


PROCEDURE

Hide 77701W 1.INSTALL NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.

Engage the 2 clamps to install the No. 1 canister outlet hose sub-assembly to the fuel tank assembly.


Hide 77028F 2.INSTALL NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY

a.

Engage the 2 clamps to install the No. 2 fuel emission tube sub-assembly to the fuel tank assembly.


Hide 77209F 3.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Engage the 2 clamps to install the fuel tank main tube sub-assembly to the fuel tank assembly.


Hide 77100 4.INSTALL FUEL TANK ASSEMBLY

a.

Clean and degrease the bolt holes.


b.

Using an engine lifter, set the fuel tank assembly.


c.

Install the fuel tank assembly to the vehicle with 4 new bolts.

Torque:
14.3 N*m (146 kgf*cm, 11 ft.*lbf)


Hide 77213B 5.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.

Connect the fuel tank to filler pipe hose to the fuel tank assembly and tighten the hose clamp.


Hide 6.CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY

a.

Connect the fuel tank breather tube sub-assembly to the fuel tank breather tube connector and tighten the hose clamp.


Hide 77701W 7.CONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.

Connect the No. 1 canister outlet hose sub-assembly to the No. 6 fuel tank breather tube.


Hide 77209F 8.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A313097C01
2.552,2.604 2.781,2.354 false 2.146,2.594 1.927,2.344 false 0.969,2.542 0.75,2.292 false 1.188,3.792 0.938,3.552 false 2.396,4.396 2.646,4.135 false 2.344,4.51 2.667,4.51 false 2.219,4.104 2.479,3.823 true 1.688,4.167 1.99,3.698 1.99,3.698 1.833,4.156 true 2.813,2.281 3.125,2.438 0.313,0.156 10 false *1 0.573,2.208 0.885,2.365 0.313,0.156 10 false *2 2.708,4.438 3.021,4.594 0.313,0.156 10 false *3 2.677,4.073 2.99,4.229 0.313,0.156 10 false *4 0.75,3.469 1.063,3.625 0.313,0.156 10 false *5 2.01,3.615 2.323,3.771 0.313,0.156 10 false *6 1.75,2.281 2.063,2.438 0.313,0.156 10 false *1 2.521,3.729 2.833,3.885 0.313,0.156 10 false *1
*1 Retainer
*2 Fuel Tube Connector Cover
*3 Fuel Tube Connector
*4 Fuel Pipe
*5 Nylon Tube
*6 O-ring
V100135

Push


Line up the fuel main tube and fuel tube connector, and push them together until a "click" sound is heard. If the fuel main tube is difficult to push into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel main tube and reinsert it.


b.

Engage the lock of the fuel tube connector cover.

NOTICE:
·

Check that there is no damage or foreign matter around the connecting parts of the fuel tube connector and fuel main tube before starting this step.

·

After connecting the fuel tube connector, check that it is securely connected by pulling on it.




Hide 77028F 9.CONNECT NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY

a.

Connect the No. 2 fuel emission tube sub-assembly to the fuel tank to canister tube and slide the hose clip to secure it.


Hide 46420 10.CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

a.

Connect the No. 2 parking brake cable assembly to the vehicle with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 77641A 11.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the No. 1 fuel tank protector to the vehicle with the bolt and clip.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 58156 12.INSTALL NO. 4 FRONT FLOOR HEAT INSULATOR

a.
A313093E01
2.896,1.76 3.052,1.958 0.156,0.198 10 false A 1.313,0.99 1.469,1.188 0.156,0.198 10 false B

Install the No. 4 front floor heat insulator to the vehicle with the 2 nuts.

Torque:
Nut A : 5.4 N*m (55 kgf*cm, 48 in.*lbf)
Nut B : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17410 13.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 14.INSTALL FRONT FLOOR CENTER BRACE

Hide 77020A 16.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 17.ADD FUEL

Hide 19.INSPECT FOR EXHAUST GAS LEAK