CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY COMPUTER (w/ Power Door Lock)
| *1 | Driver Side Junction Block Assembly | - | - |
| *1 | Body Computer | - | - |
Remove the body computer from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| MB-6 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| MB-7 (IG) - Body ground | - | IG power supply | Ignition switch ON | 11 to 14 V |
| MB-1 (GND) - Body ground | - | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Install the body computer to the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 2D-13 (ILE) - Body ground | GR - Body ground | Illumination signal | Map light switch in door position and map light assembly comes on | Below 1 V |
| Map light switch in door position and map light assembly goes off | 11 to 14 V | |||
| 2N-1 (DCTY) - Body ground | BR - Body ground | Driver side door courtesy light switch signal | Driver side door opened | Below 1 V |
| Driver side door closed | Pulse generation | |||
| 2N-3 (LGCY) - Body ground*5 | R - Body ground | Luggage compartment door lock assembly signal | Luggage compartment door opened | Below 1 V |
| Luggage compartment door closed | 11 to 14 V | |||
| 2N-3 (BCTY) - Body ground*6 | R - Body ground | Back door lock assembly signal | Back door opened | Below 1 V |
| Back door closed | 11 to 14 V | |||
| F52-14 (PCTY) - Body ground | LG - Body ground | Except driver side door courtesy light switch signal | Except driver side door opened | Below 1 V |
| Except driver side door closed | Pulse generation | |||
| F52-15 (LSWD)- Body ground | L - Body ground*3
W - Body ground*4 |
Driver side door unlock detection switch signal | Driver side door locked | Pulse generation |
| Driver side door unlocked | Below 1 V | |||
| F52-8 (KSW)- Body ground*1 | SB - Body ground | Unlock warning switch assembly signal | No key in ignition key cylinder | Pulse generation |
| Key in ignition key cylinder | Below 1 V | |||
| F52-9 (PRG) - Body ground*2 | BR - Body ground | Signal output to certification ECU (smart key ECU assembly) | Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| F52-16 (RDA) - Body ground*2 | GR - Body ground | Signal input from certification ECU (smart key ECU assembly) | Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation |
*1: w/o Smart Entry and Start System
*2: w/ Smart Entry and Start System
*3: for LHD
*4: for RHD
*5: for Sedan
*6: for Hatchback
If the result is not as specified, the body computer or driver side junction block assembly may be malfunctioning.
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F43-10 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the F43 certification ECU (smart key ECU assembly) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F43-19 (SWIL) - F43-24 (AGND) | P - G | Engine switch illumination drive output | Engine switch illumination on | 9 to 14 V |
| Engine switch illumination off | Below 1 V | |||
| F43-9 (LSWP) - F43-10 (E) | W - W-B | Except front door RH unlock detection switch input | Engine switch off, all doors closed, all doors unlocked and electrical key transmitter sub-assembly lock switch not pressed | Below 1 V |
| Engine switch off, all doors closed, all doors unlocked and electrical key transmitter sub-assembly lock switch pressed | 8.5 V or higher | |||
| F44-13 (RDA3) - F43-10 (E) | GR - W-B | Signal output to body computer | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| F44-36 (PRG3) - F43-10 (E) | BR - W-B | Signal input from body computer | Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch not pressed | 11 to 14 V |
| Engine switch off, all doors closed, 10 seconds elapsed after all doors locked and electrical key transmitter sub-assembly unlock switch pressed | Pulse generation | |||
| F43-21 (ACCD) - F43-10 (E) | L - W-B | ACC signal | Engine switch off → Engine switch on (ACC) | 1 V or less → 8.5 V or higher |
| F43-20 (IG1D) - F43-10 (E) | BR - W-B | IG1 signal | Engine switch on (ACC) → Engine switch on (IG) | 1 V or less → 9 V or higher |
| F44-10 (TLH) - F43-10 (E) | SB - W-B | Tail light signal | Light control switch OFF → Light control switch Tail | Below 1 V → 11 to 14 V |
If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.