Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › 2014.03–2016.07
RM30M0E _51 Engine / Hybrid System _017071 1NZ-FE ENGINE CONTROL _0116465 SFI SYSTEM(w/ Air Fuel Ratio Sensor) J

1NZ-FE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the starter relay assembly drive signal output from the ignition or starter switch assembly is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. The ECM interprets that the engine is cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input into the ECM with the engine running, the ECM turns Tr1 on continuously.

WIRING DIAGRAM

A310015E03
0.865,0.552 1.021,0.75 0.156,0.198 10 false 5 1.042,0.552 1.438,0.771 0.396,0.219 10 false AM2 2.208,0.542 2.604,0.76 0.396,0.219 10 false IG2 2.51,0.542 2.667,0.74 0.156,0.198 10 false 6 0.688,0.979 1.083,1.198 0.396,0.219 10 false F7 0.698,1.125 2.927,1.375 2.229,0.25 10 false Ignition or Starter Switch Assembly 1.219,1.563 1.375,1.76 0.156,0.198 10 false 5 1.167,1.75 1.479,1.948 0.313,0.198 10 false 2H 1.656,2.125 2.052,2.344 0.396,0.219 10 false AM2 1.219,2.531 1.375,2.729 0.156,0.198 10 false 1 1.177,2.729 1.49,2.927 0.313,0.198 10 false 2B 1.563,2.875 2.229,3.083 0.667,0.208 10 false EFI-MAIN 1.188,3.271 1.5,3.469 0.313,0.198 10 false 2J 1.229,3.083 1.385,3.281 0.156,0.198 10 false 7 1,3.885 3.302,4.115 2.302,0.229 10 false Driver Side Junction Block Assembly 2.49,3.542 2.844,3.74 0.354,0.198 10 false EFI 2.958,3.656 3.115,3.854 0.156,0.198 10 false 4 3.198,3.656 3.51,3.854 0.313,0.198 10 false 2K 3.125,1.552 3.438,1.75 0.313,0.198 10 false 2H 2.885,1.552 3.042,1.75 0.156,0.198 10 false 1 3.292,1.917 3.979,2.115 0.688,0.198 10 false IG2 NO. 1 4.625,2.104 4.781,2.302 0.156,0.198 10 false 8 4.594,2.302 4.906,2.5 0.313,0.198 10 false 2L 4.635,2.542 4.792,2.74 0.156,0.198 10 false 7 4.583,2.729 4.896,2.927 0.313,0.198 10 false 2O 4.635,3.073 4.792,3.271 0.156,0.198 10 false 9 4.604,3.271 4.917,3.469 0.313,0.198 10 false 2L 3.75,3.042 4.281,3.25 0.531,0.208 10 false C/OPN 0.469,4.156 1.135,4.365 0.667,0.208 10 false MAIN 0.458,4.677 1.125,4.885 0.667,0.208 10 false FL MAIN 0.625,5.354 1.292,5.563 0.667,0.208 10 false Battery 1.583,5.24 2.385,5.458 0.802,0.219 10 false Fuel Pump 1.5,4.708 1.656,4.906 0.156,0.198 10 false 4 1.49,4.927 1.646,5.125 0.156,0.198 10 false B 1.5,5.792 1.656,5.99 0.156,0.198 10 false 5 1.49,5.583 1.646,5.781 0.156,0.198 10 false E 2.333,5 2.729,5.219 0.396,0.219 10 false F28 2.333,5.177 4.198,5.563 1.865,0.385 10 false Fuel Suction Tube with Pump and Gauge Assembly 5.729,2.313 6.125,2.531 0.396,0.219 10 false F83 5.719,3.271 6.115,3.49 0.396,0.219 10 false F83 5.719,4.125 6.115,4.344 0.396,0.219 10 false F83 5.729,4.573 6.125,4.792 0.396,0.219 10 false F83 5.729,5 6.125,5.219 0.396,0.219 10 false F82 5.719,5.479 6.115,5.698 0.396,0.219 10 false B29 5.729,5.896 6.125,6.115 0.396,0.219 10 false B29 5.76,2.104 6.146,2.292 0.385,0.188 10 false 10 5.802,3.063 6.042,3.26 0.24,0.198 10 false 8 5.802,3.927 6.042,4.125 0.24,0.198 10 false 1 5.802,4.375 6.042,4.573 0.24,0.198 10 false 2 5.771,4.792 6.01,4.99 0.24,0.198 10 false 19 5.771,5.271 6.01,5.469 0.24,0.198 10 false 27 5.771,5.708 6.01,5.906 0.24,0.198 10 false 34 6.083,2.448 6.479,2.667 0.396,0.219 10 false FC 6.083,3.271 6.563,3.49 0.479,0.219 10 false MREL 6.083,4.115 6.563,4.333 0.479,0.219 10 false +B 6.083,4.563 6.563,4.781 0.479,0.219 10 false +B2 6.083,4.99 6.563,5.208 0.479,0.219 10 false STA 6.083,5.458 6.563,5.677 0.479,0.219 10 false NE+ 6.083,5.896 6.563,6.115 0.479,0.219 10 false NE- 6.344,6.323 6.823,6.542 0.479,0.219 10 false ECM 4.208,5 5.229,5.375 1.021,0.375 10 false from STA Signal Circuit 4.229,5.604 5.271,5.99 1.042,0.385 10 false from Crankshaft Position Sensor 6.646,2.271 7.042,2.49 0.396,0.219 10 false Tr1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.


Result:
Result Proceed to
Fuel pump operating sound does not occur A
Fuel pump operating sound occurs B



A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)

B

11.READ VALUE USING GTS (STARTER SIGNAL)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the C/OPN relay operating sound occurs when performing the Active Test on the GTS.

OK:

Relay operating sounds can be heard from the relay.



Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL PUMP

NG

7.CHECK TERMINAL VOLTAGE (FC TERMINAL VOLTAGE)
3.INSPECT FUEL PUMP
a.

Result:
Proceed to
OK
NG



OK

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)

NG

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)
a.

Remove the driver side junction block assembly

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

A319971C08
5.177,0.198 5.469,0.375 0.292,0.177 2.25,0.198 2.583,0.365 0.333,0.167 4.844,0.198 5.135,0.375 0.292,0.177 5.5,0.198 5.792,0.375 0.292,0.177 5.24,0.208 5.448,0.375 0.208,0.167 10 false 2K 2.333,0.208 2.552,0.396 0.219,0.188 10 false 2O 4.927,0.208 5.135,0.354 0.208,0.146 10 false 2L 5.552,0.208 5.76,0.365 0.208,0.156 10 false 2H 0.24,0.167 0.552,0.365 0.313,0.198 10 false *a 3.792,0.208 4.104,0.406 0.313,0.198 10 false *b
*a Component without harness connected
(Driver Side Junction Block Assembly (Rear Side))
*b Component without harness connected
(Driver Side Junction Block Assembly (Front Side))


Standard Resistance:
Tester Connection Condition Specified Condition
2K-4 - 2O-7 When battery voltage not applied to terminals 2L-8 and 2H-1 10 kΩ or higher
When battery voltage applied to terminals 2L-8 and 2H-1 Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Disconnect the F28 fuel suction tube with pump and gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2O-7 - F28-4 (B) Always Below 1 Ω
2O-7 or F28-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - BODY GROUND)
a.

Disconnect the F28 fuel suction tube with pump and gauge assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F28-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TERMINAL VOLTAGE (FC TERMINAL VOLTAGE)
a.
A301710C02
2.188,0.271 2.552,0.531 0.365,0.26 2.01,1.635 2.458,0.833 true 2.229,0.313 2.688,0.51 0.458,0.198 10 false F83 1.906,1.74 2.365,1.938 0.458,0.198 10 false FC 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F83-10 (FC) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
NG A
OK B



A

8.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)

B

8.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

A319971C08
5.177,0.198 5.469,0.375 0.292,0.177 2.25,0.198 2.583,0.365 0.333,0.167 4.844,0.198 5.135,0.375 0.292,0.177 5.5,0.198 5.792,0.375 0.292,0.177 5.24,0.208 5.448,0.375 0.208,0.167 10 false 2K 2.333,0.208 2.552,0.396 0.219,0.188 10 false 2O 4.927,0.208 5.135,0.354 0.208,0.146 10 false 2L 5.552,0.208 5.76,0.365 0.208,0.156 10 false 2H 0.24,0.167 0.552,0.365 0.313,0.198 10 false *a 3.792,0.208 4.104,0.406 0.313,0.198 10 false *b
*a Component without harness connected
(Driver Side Junction Block Assembly
(Rear Side))
*b Component without harness connected
(Driver Side Junction Block Assembly
(Front Side))


Standard Resistance:
Tester Connection Condition Specified Condition
2K-4 - 2O-7 When battery voltage not applied to terminals 2L-8 and 2H-1 10 kΩ or higher
When battery voltage applied to terminals 2L-8 and 2H-1 Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - ECM)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - ECM)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Disconnect the F83 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2L-8 - F83-10 (FC) Always Below 1 Ω
2L-8 or F83-10 (FC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - IGNITION OR STARTER SWITCH ASSEMBLY)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Disconnect the F7 ignition or starter switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2H-1 - F7-6 (IG2) Always Below 1 Ω
2H-1 or F7-6 (IG2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Condition Starter Signal
Ignition switch ON OFF
Engine Started ON



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (ENGINE SPEED)

NG

12.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Read the values displayed on the GTS while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG