Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › 2014.03–2016.07
RM30M0E _51 Engine / Hybrid System _017071 1NZ-FE ENGINE CONTROL _0116465 SFI SYSTEM(w/ Air Fuel Ratio Sensor) J

1NZ-FE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST2 of the ignition or starter switch assembly to the park/neutral position switch*1 or clutch start switch assembly*2 and to terminal STA of the ECM (STA signal).

*1: for Automatic Transaxle

*2: for Manual Transaxle


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

19.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Result Proceed to
NG (for Automatic Transaxle) A
NG (for Manual Transaxle) B
OK C



A

3.INSPECT PARK/NEUTRAL POSITION SWITCH

B

7.INSPECT CLUTCH START SWITCH ASSEMBLY

C

11.INSPECT STARTER RELAY ASSEMBLY
3.INSPECT PARK/NEUTRAL POSITION SWITCH

Result:
Proceed to
OK
NG



OK

4.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

4.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>1NZ-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the F7 ignition or starter switch assembly connector.


b.

Disconnect the B19 park/neutral position switch connector.


c.

Disconnect the F82 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F7-7 (ST2) - B19-4 (B) Always Below 1 Ω
F7-7 (ST2) - B49-8 (NSW) Always Below 1 Ω
F7-7 (ST2), B19-4 (B) or F82-9 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STARTER RELAY ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STARTER RELAY ASSEMBLY - ECM)
a.

Disconnect the B19 park/neutral position switch connector.


b.

Remove the starter relay assembly from the engine room relay block.


c.

Disconnect the F82 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B19-5 (L) - F82-19 (STA) Always Below 1 Ω
Relay holder 2 - F82-19 (STA) Always Below 1 Ω
B19-5 (L), Relay holder 2 or F82-19 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

8.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

8.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>1NZ-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the F7 ignition or starter switch assembly connector.


b.

Disconnect the A28 clutch start switch assembly connector.


c.

Disconnect the F82 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F7-7 (ST2) - A28-2 Always Below 1 Ω
F7-7 (ST2) - F82-9 (NSW) Always Below 1 Ω
F7-7 (ST2), A28-2 or F82-9 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - STARTER RELAY ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - STARTER RELAY ASSEMBLY - ECM)
a.

Disconnect the A28 clutch start switch assembly connector.


b.

Remove the starter relay assembly from the engine room relay block.


c.

Disconnect the F82 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-1 - F82-19 (STA) Always Below 1 Ω
Relay holder 2 - F82-19 (STA) Always Below 1 Ω
Relay holder 2, F82-19 (STA) or A28-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT STARTER RELAY ASSEMBLY
a.

Inspect the starter relay assembly.

Click hereEngine / Hybrid System>1NZ-FE STARTING>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

12.INSPECT STARTER ASSEMBLY

NG

REPLACE STARTER RELAY ASSEMBLY

12.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.

Click hereEngine / Hybrid System>1NZ-FE STARTING>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - STARTER ASSEMBLY)

NG

REPLACE STARTER ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - STARTER ASSEMBLY)
a.

Remove the starter relay assembly from the engine room relay block.


b.

Disconnect the B15 starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay holder 3 - B15-1 Always Below 1 Ω
Relay holder 3 or B15-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the B28 starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - B28-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER RELAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER RELAY ASSEMBLY)
a.
A301476C02
0.146,0.198 0.458,0.354 0.313,0.156 10 false *1 0.229,1.469 0.542,1.625 0.313,0.156 10 false *2
*1 Engine Room Relay Block
*2 Relay holder (Starter Relay Assembly)


Remove the starter relay assembly from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay holder 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER RELAY ASSEMBLY)

16.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - BODY GROUND)
a.

Remove the starter relay assembly from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay holder 1 - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for Automatic Transaxle) A
OK (for Manual Transaxle) B
NG C



A

17.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - PARK/NEUTRAL POSITION SWITCH)

B

18.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - PARK/NEUTRAL POSITION SWITCH)
a.

Remove the starter relay assembly from the engine room relay block.


b.

Disconnect the B19 park/neutral position switch connector.


c.

Disconnect the F82 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay holder 2 - B19-5 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
a.

Remove the starter relay assembly from the engine room relay block.


b.

Disconnect the A28 clutch start switch assembly connector.


c.

Disconnect the F82 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay holder 2 - A28-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

20.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - ECM)
20.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - ECM)
a.

Remove the starter relay assembly from the engine room relay block.


b.

Disconnect the F82 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay holder 2 - F82-19 (STA) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR