Home › Vehicle Interior › SEAT BELT › REAR CENTER SEAT OUTER BELT ASSEMBLY › 2014.03–2017.10
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0116526 REAR CENTER SEAT OUTER BELT ASSEMBLY A

SEAT BELT  REAR CENTER SEAT OUTER BELT ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 73310D 1.INSPECT REAR CENTER SEAT 3 POINT TYPE BELT ASSEMBLY

a.
B349246C01
0.385,1.198 0.698,1.396 0.313,0.198 10 false *a 1.135,3.042 1.448,3.24 0.313,0.198 10 false *b 0.479,2.229 0.792,2.427 0.313,0.198 10 false 45°
*a Unlock
*b Lock


Check the angle of inclination required to lock the retractor.

i.

Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

NOTICE:

Do not disassemble the retractor.

If the operation is not as specified, replace the rear center seat 3 point type belt assembly.




Hide 73310D 2.INSTALL REAR CENTER SEAT 3 POINT TYPE BELT ASSEMBLY

a.
B345189C06
1.99,0.594 1.49,0.323 true 1.719,1.177 1.323,1.083 true 1.333,0.219 1.646,0.417 0.313,0.198 10 false *a 1.125,0.979 1.438,1.177 0.313,0.198 10 false *b 2.604,0.76 2.917,0.958 0.313,0.198 10 true A 1.76,1.771 1.99,1.979 0.229,0.208 10 true B 2.479,0.427 2.646,0.615 0.167,0.188 10 true C
*a Guide Anchor
*b Retractor


Insert the hook into the body hole to install the retractor of the rear center seat 3 point type belt assembly.


b.

Temporarily install the bolt A and bolt B.


c.

Tighten bolt A and then bolt B.

Torque:
for Bolt A : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
for Bolt B : 42 N*m (428 kgf*cm, 31 ft.*lbf)


d.

Engage the hook to connect the guide anchor of the rear center seat 3 point type belt assembly.


e.

Install the bolt C.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


f.

Connect the slip anchor of the rear center seat 3 point type belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


g.

Check that the ELR locks.

NOTICE:

Perform the check with the rear center seat 3 point type belt assembly.


i.

With the belt installed, check that the belt locks when it is pulled out quickly.

If the operation is not as specified, replace the rear center seat 3 point type belt assembly.



h.

Loosen the bolt to disconnect the slip anchor of the rear center seat 3 point type belt assembly.


Hide 62472A 3.INSTALL ROOF SIDE INNER GARNISH LH

Hide 73310D 4.CONNECT REAR CENTER SEAT 3 POINT TYPE BELT ASSEMBLY

a.

Engage the 2 guides and 3 claws to connect the belt guide of the rear center seat 3 point type belt assembly to the roof side inner garnish LH.


b.

Connect the slip anchor of the rear center seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Engage the 2 claws to close the guide cover of the rear center seat 3 point type belt assembly.


Hide 62572A 5.INSTALL ROOF SIDE INNER LOWER GARNISH LH

Hide 73370 7.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

Hide 64740C 8.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

Hide 62332A 9.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 10.INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)

Hide 11.INSTALL REAR SEAT ASSEMBLY (for Separate Seat Type)

Hide 64773B 13.INSTALL NO. 2 SPARE WHEEL COVER PAD

Hide 64711E 16.INSTALL LUGGAGE COMPARTMENT FLOOR MAT

Hide 81330 17.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Hide 64330 18.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY