1.INSTALL ROOF HEADLINING ASSEMBLY
Put the roof headlining assembly into the vehicle through the back door.
Do not damage the roof headlining assembly or body interior.
Install the roof headlining assembly with the 4 clips.
for front pillar RH side:
Install the 2 clamps.
Engage the guide and install the bolt.
Connect the connector.
for front pillar LH side:
Install the 2 clamps.
Connect the connector.
for rear pillar RH side:
Install the clamp.
Connect the connector.
74348C
2.INSTALL VISOR HOLDER LH
74348B
3.INSTALL VISOR HOLDER RH
Use the same procedure as for the LH side.
74320
4.INSTALL VISOR ASSEMBLY LH
74310
5.INSTALL VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74610A
6.INSTALL ASSIST GRIP SUB-ASSEMBLY
81260A
7.INSTALL MAP LIGHT ASSEMBLY
62472A
8.INSTALL ROOF SIDE INNER GARNISH LH
Pass the slip anchor of the rear center seat outer belt assembly through the roof side inner garnish LH.
Engage the guide and 6 clips to install the roof side inner garnish LH.
62471A
9.INSTALL ROOF SIDE INNER GARNISH RH
Engage the guide and 6 clips to install the roof side inner garnish RH.
73310D
10.CONNECT REAR CENTER SEAT 3 POINT TYPE BELT ASSEMBLY (for 3 Point Type Rear Center Seat Belt)
62572A
11.INSTALL ROOF SIDE INNER LOWER GARNISH LH
Engage the 2 clips and 5 claws to install the roof side inner lower garnish LH.
Install the screw.
62571A
12.INSTALL ROOF SIDE INNER LOWER GARNISH RH
Use the same procedure as for the LH side.
81330
13.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
62552F
14.INSTALL REAR SEAT SIDE GARNISH LH
Engage the clip and 2 claws to install the rear seat side garnish LH.
62551F
15.INSTALL REAR SEAT SIDE GARNISH RH
Use the same procedure as for the LH side.
73370
16.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
73360
17.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
64740C
18.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
Install the deck trim side panel assembly LH with the 7 clips.
64730B
19.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
Use the same procedure as for the LH side.
64716D
20.INSTALL REAR DECK TRIM COVER
Engage the 2 guides and 4 claws to install the rear deck trim cover.
Install the 2 clips.
62412B
21.INSTALL CENTER PILLAR UPPER GARNISH LH
62411B
22.INSTALL CENTER PILLAR UPPER GARNISH RH
Use the same procedure as for the LH side.
62414A
23.INSTALL CENTER PILLAR LOWER GARNISH LH
62413A
24.INSTALL CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
73220
25.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
73210
26.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62332A
27.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
| *a | Paint Mark |
| *b | Flange Position |
Align the paint mark on the rear door opening trim weatherstrip LH with the flange position on the vehicle body and install the rear door opening trim weatherstrip LH.
| Area | Color |
|---|---|
| LH Side | Red |
| RH Side | Green |
After installation, check that the corners fit correctly.
62331A
28.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62212
29.INSTALL FRONT PILLAR GARNISH LH
62211
30.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
62312B
31.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
32.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62112
33.INSTALL COWL SIDE TRIM BOARD LH
62111C
34.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
35.INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)
36.INSTALL REAR SEAT ASSEMBLY (for Separate Seat Type)
64773B
37.INSTALL NO. 2 SPARE WHEEL COVER PAD
Install the No. 2 spare wheel cover pad.
64772
38.INSTALL SPARE WHEEL COVER PAD
Install the spare wheel cover pad.
58410B
39.INSTALL DECK BOARD ASSEMBLY
Install the deck board assembly.
64711E
40.INSTALL LUGGAGE COMPARTMENT FLOOR MAT
Install the luggage compartment floor mat.
41.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
Engage the 2 guides to install the package tray trim panel assembly.
Install the 2 suspenders onto the package tray trim hanger.