Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR › 2014.03–2016.04
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090185 BRAKE ACTUATOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR  INSTALLATION  


PROCEDURE

Hide 44546A 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

a.

Install the 3 brake actuator bracket cushions to the brake actuator bracket assembly.


b.

Install the 3 brake actuator case collars to the 3 brake actuator bracket cushions.


Hide 44590 2.INSTALL BRAKE ACTUATOR BRACKET ASSEMBLY (for LHD)

a.
C286077E01
0.771,0.656 0.927,0.854 0.156,0.198 10 false 1 1.885,0.344 2.042,0.542 0.156,0.198 10 true 2 1.531,1.552 1.688,1.75 0.156,0.198 10 false 3

Install the brake actuator bracket assembly to the brake actuator assembly with the 3 bolts in the sequence shown in the illustration.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not remove the hole plug before connecting the brake tube. New actuators are filled with brake fluid.

·

Do not carry the brake actuator assembly by the connector.




Hide 44590 3.INSTALL BRAKE ACTUATOR BRACKET ASSEMBLY (for RHD)

a.
C169913E01
0.635,0.563 0.792,0.76 0.156,0.198 10 false 1 1.906,0.198 2.135,0.427 0.229,0.229 10 true 2 1.458,1.542 1.688,1.771 0.229,0.229 10 true 3

Install the brake actuator bracket assembly to the brake actuator assembly with the 3 bolts in the sequence shown in the illustration.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not remove the hole plug before connecting the brake tube. New actuators are filled with brake fluid.

·

Do not carry the brake actuator assembly by the connector.




Hide 44510 4.INSTALL BRAKE ACTUATOR ASSEMBLY (for LHD)

a.
C286076E01
1,1.719 1.156,1.917 0.156,0.198 10 false 1 2.531,1.688 2.688,1.885 0.156,0.198 10 false 2 2.823,1.083 2.979,1.281 0.156,0.198 10 true 3

Install the brake actuator assembly with the brake actuator bracket assembly with the 3 bolts in the sequence shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not damage the brake tubes or wire harness.

·

Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.




b.
C286826C01
1.156,1.25 1.344,1.042 true 0.479,0.5 0.885,0.792 true 0.719,0.26 1.125,0.552 true 1.667,0.708 1.917,0.458 true 1.51,0.625 1.885,0.24 true 1.354,0.583 1.438,0.26 true 0.531,0.135 0.844,0.292 0.313,0.156 10 false *a 1.938,0.354 2.25,0.51 0.313,0.156 10 false *b 1.906,0.146 2.094,0.323 0.188,0.177 10 true *c 1.458,0.156 1.635,0.313 0.177,0.156 10 false *d 0.323,0.396 0.635,0.552 0.313,0.156 10 false *e 1.031,1.24 1.344,1.396 0.313,0.156 10 false *f
*a to Front Wheel Cylinder RH
*b to Front Wheel Cylinder LH
*c to Rear Wheel Cylinder RH
*d to Rear Wheel Cylinder LH
*e from Front Master Cylinder
*f from Rear Master Cylinder


Temporarily install each brake tube to the correct position on the brake actuator assembly as shown in the illustration.


c.

Using a 10 mm union nut wrench, tighten the 6 brake tubes.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



d.
C285143C01
1.219,1.229 1.708,1.344 false 1.75,1.26 2.063,1.417 0.313,0.156 10 false *a
*a Lock Lever


Connect the brake actuator connector.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the brake actuator connector can be connected smoothly. Do not allow entry of water, oil or dirt.




Hide 44510 5.INSTALL BRAKE ACTUATOR ASSEMBLY (for RHD)

a.
C169912E02
1.073,1.719 1.198,1.906 0.125,0.188 10 true 1 2.708,1.667 2.823,1.844 0.115,0.177 10 true 2 2.677,0.979 2.927,1.156 0.25,0.177 10 true 3

Install the brake actuator assembly with the brake actuator bracket assembly with the 3 bolts in the sequence shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not damage the brake tubes or wire harness.

·

Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.




b.
C287089C01
1.229,1.271 1.396,1.042 true 0.948,0.792 0.583,0.49 true 1.708,0.719 2.01,0.458 true 1.563,0.646 1.844,0.24 true 1.177,0.563 0.844,0.188 true 1.427,0.594 1.615,0.177 true 0.677,0.073 0.99,0.229 0.313,0.156 10 false *a 2.031,0.354 2.344,0.51 0.313,0.156 10 false *b 1.875,0.125 2.188,0.281 0.313,0.156 10 false *c 1.656,0.073 1.833,0.229 0.177,0.156 10 true *d 0.427,0.365 0.74,0.521 0.313,0.156 10 false *e 1.094,1.198 1.26,1.385 0.167,0.188 10 false *f
*a to Front Wheel Cylinder RH
*b to Front Wheel Cylinder LH
*c to Rear Wheel Cylinder RH
*d to Rear Wheel Cylinder LH
*e from Rear Master Cylinder
*f from Front Master Cylinder


Temporarily install each brake tube to the correct position on the brake actuator assembly as shown in the illustration.


c.

Using a 10 mm union nut wrench, tighten the 6 brake tubes.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



d.
C285143C01
1.219,1.229 1.708,1.344 false 1.75,1.26 2.063,1.417 0.313,0.156 10 false *a
*a Lock Lever


Connect the brake actuator connector.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the brake actuator connector can be connected smoothly. Do not allow entry of water, oil or dirt.




Hide 74410 6.INSTALL BATTERY CARRIER ASSEMBLY

a.
C283246E01
0.875,0.76 1.021,0.927 0.146,0.167 10 true A 2.198,0.583 2.344,0.75 0.146,0.167 10 true A 2.26,1.125 2.406,1.292 0.146,0.167 10 true A 2.792,1.281 2.938,1.448 0.146,0.167 10 true A 2.385,1.844 2.531,2.01 0.146,0.167 10 true A 0.76,1.958 0.906,2.125 0.146,0.167 10 true B

Install the battery carrier assembly to the body with the 6 bolts.

Torque:
Bolt A : 17.2 N*m (175 kgf*cm, 13 ft.*lbf)
Bolt B : 7.8 N*m (80 kgf*cm, 69 in.*lbf)


b.

Engage the 6 clamps to install the wire harness to the battery carrier assembly.


Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 11.BLEED CLUTCH LINE (for Manual Transaxle)