Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER(for LHD) › 2014.03–2016.04
RM30M0E _54 Brake _017099 BRAKE SYSTEM (OTHER) _0092757 BRAKE MASTER CYLINDER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for LHD)  INSTALLATION  


PROCEDURE

Hide 47201 1.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ ABS)

a.

Install a new O-ring to the brake master cylinder sub-assembly.


b.

Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.

Using a 10 mm union nut wrench, connect the 2 brake tubes to the brake master cylinder sub-assembly.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



d.

Engage the wire harness clamp.


e.

Connect the brake fluid level warning switch connector.


f.

Using a 10 mm union nut wrench, connect the 6 brake tubes to the brake actuator assembly.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



g.

Using a 10 mm union nut wrench, connect the 2 brake tubes to the front No. 1 brake tube way.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 47201 2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/o ABS)

a.

Install a new O-ring to the brake master cylinder sub-assembly.


b.

Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.

Using a 10 mm union nut wrench, connect the 2 brake tubes to the brake master cylinder sub-assembly.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



d.

Engage the wire harness clamp.


e.

Connect the brake fluid level warning switch connector.


f.

Using a 10 mm union nut wrench, connect the 6 brake tubes to the proportioning valve assembly.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



g.

Using a 10 mm union nut wrench, connect the 2 brake tubes to the front No. 1 brake tube way.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 31434C 3.INSTALL CLUTCH RESERVOIR TUBE (for Manual Transaxle)

a.

Connect the clutch reservoir tube to the brake master cylinder sub-assembly with the hose clip.


Hide 74410 4.INSTALL BATTERY CARRIER ASSEMBLY

Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 9.BLEED CLUTCH LINE (for Manual Transaxle)