Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › 2014.03–2017.10
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090849 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Back Door Entry Lock Function does not Operate  


DESCRIPTION

If the entry lock function does not operate for the back door only, but the entry unlock function operates, the request code is being transmitted properly from the back door. In this case, there may be a problem related to the lock switch (connection between the back door opener switch assembly and certification ECU (smart key ECU assembly)).

WIRING DIAGRAM

B359805E07
0.688,1.333 0.844,1.531 0.156,0.198 10 false 2 1.99,0.906 2.146,1.104 0.156,0.198 10 false 3 1.99,1.333 2.146,1.531 0.156,0.198 10 false 1 0.823,1.729 1.156,1.896 0.333,0.167 10 false R1 0.833,1.917 2,2.333 1.167,0.417 10 false Back Door Opener Switch Assembly 3.021,0.844 3.302,1.021 0.281,0.177 10 false 14 2.979,1 3.344,1.229 0.365,0.229 10 false F43 2.979,1.438 3.344,1.667 0.365,0.229 10 false F43 2.99,1.948 3.354,2.177 0.365,0.229 10 false F43 4.198,1.208 4.563,1.438 0.365,0.229 10 false F44 4.198,1.698 4.563,1.927 0.365,0.229 10 false F44 3.031,1.271 3.313,1.448 0.281,0.177 10 false 23 3.021,1.781 3.302,1.958 0.281,0.177 10 false 10 4.24,1.042 4.521,1.219 0.281,0.177 10 false 36 4.24,1.531 4.521,1.708 0.281,0.177 10 false 13 3.292,1.01 3.844,1.219 0.552,0.208 10 false TSW5 3.75,1.219 4.302,1.427 0.552,0.208 10 false PRG3 3.76,1.719 4.313,1.927 0.552,0.208 10 false RDA3 3.292,1.448 3.844,1.656 0.552,0.208 10 false TSW6 3.302,1.958 3.667,2.188 0.365,0.229 10 false E 3,2.479 4.521,2.875 1.521,0.396 10 false Certification ECU (Smart Key ECU Assembly) 5.323,1.125 5.604,1.302 0.281,0.177 10 false 9 5.281,1.625 5.563,1.802 0.281,0.177 10 false 16 5.51,1.208 6.063,1.417 0.552,0.208 10 false PRG 5.51,1.698 6.063,1.906 0.552,0.208 10 false RDA 5.458,2.469 5.823,2.698 0.365,0.229 10 false F52 5.458,2.615 6.792,2.844 1.333,0.229 10 false Body Computer

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) or B27B0 is not output.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (TR/B-DOOR LOCK SW)

NG

2.READ VALUE USING GTS (TR/B-DOOR LOCK SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tr/B-Door Lock SW Back door opener switch assembly (lock switch) ON or OFF ON: Back door opener switch assembly (lock switch) pushed
OFF: Back door opener switch assembly (lock switch) not pushed
·

Displays whether the back door opener switch assembly (lock switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the back door lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Tr/B-Door Lock SW
50003 125 16
OK:

The GTS display changes correctly in response to the operation of the back door opener switch assembly.



Result:
Result Proceed to
NG A
OK B



A

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BACK DOOR OPENER SWITCH ASSEMBLY)

B

5.CHECK ENTRY BACK DOOR UNLOCK OPERATION
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BACK DOOR OPENER SWITCH ASSEMBLY)
a.

Disconnect the F43 and certification ECU (smart key ECU assembly) connector.


b.

Disconnect the R1 back door opener switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-23 (TSW6) - R1-1 Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
R1-2 - Body ground Always Below 1 Ω
F43-23 (TSW6) or R1-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
a.

Remove the back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL


b.

Inspect the back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK ENTRY BACK DOOR UNLOCK OPERATION

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

5.CHECK ENTRY BACK DOOR UNLOCK OPERATION
a.

Check the entry back door unlock operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and back door opener switch assembly before performing the inspection.


OK:

Entry back door unlock operates normally.



Result:
Proceed to
OK
NG



OK

END (CONNECT CONNECTORS PROPERLY)

NG

6.REPLACE BODY COMPUTER
6.REPLACE BODY COMPUTER
a.

Replace the body computer with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK ENTRY BACK DOOR LOCK OPERATION
7.CHECK ENTRY BACK DOOR LOCK OPERATION
a.

Check the entry back door lock operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry back door lock operates normally.



Result:
Proceed to
OK
NG



OK

END (BODY COMPUTER WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)