Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT › 2014.03–2017.10
RM30M0E _53 Suspension _017094 ALIGNMENT / HANDLING DIAGNOSIS _0090094 REAR WHEEL ALIGNMENT G

ALIGNMENT / HANDLING DIAGNOSIS  REAR WHEEL ALIGNMENT  INSPECTION  


PROCEDURE

Hide 3.MEASURE VEHICLE HEIGHT (for Hatchback)

Hide 4.INSPECT CAMBER

NOTICE:

Inspect while the vehicle is unloaded.


a.

Remove the wheel cap or wheel hub ornament.


b.

Install the camber-caster-kingpin gauge and position the rear wheel on the turning radius gauge.


c.

Inspect the camber.

Camber (Unloaded Vehicle):
except for Rough Road Package
Camber Inclination Right-left Difference
-0°56' +/- 0°45' (-0.93° +/- 0.75°) 0°45' (0.75°) or less

for Rough Road Package
Camber Inclination Right-left Difference
-0°54' +/- 0°45' (-0.90° +/- 0.75°) 0°45' (0.75°) or less


If the camber is not within the specified range, inspect the suspension parts for damage and wear, and replace them if necessary.


d.

Remove the camber-caster-kingpin gauge.


e.

Install the wheel cap or wheel hub ornament.


Hide 5.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to neutral.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968C19
2.521,1.333 2.521,1.667 false 0.823,0.552 0.844,1.094 0.844,1.094 1.333,0.594 true 0.76,1.135 0.938,1.302 0.177,0.167 10 false *a 2.427,1.698 2.604,1.854 0.177,0.156 10 false *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

NOTICE:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.



f.
C188969C02
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

Toe-in (Unloaded Vehicle):
except for Rough Road Package
Tire Size Specified Condition
175/65R14 C + D: 0°18' +/- 0°15' (0.30° +/- 0.25°)
B - A: 3.1 +/- 3.0 mm (0.122 +/- 0.118 in.)
185/60R15 C + D: 0°18' +/- 0°15' (0.30° +/- 0.25°)
B - A: 3.2 +/- 3.0 mm (0.126 +/- 0.118 in.)

for Rough Road Package
Tire Size Specified Condition
175/65R14 C + D: 0°14' +/- 0°15' (0.23° +/- 0.25°)
B - A: 2.5 +/- 3.0 mm (0.0984 +/- 0.118 in.)
185/60R15 C + D: 0°14' +/- 0°15' (0.23° +/- 0.25°)
B - A: 2.7 +/- 3.0 mm (0.106 +/- 0.118 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, inspect the suspension parts for damage and wear, and replace them if necessary.