Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2015.01–2017.10
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090853 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  While Alarm is Armed, Luggage Door or Engine Hood is opened but Alarm does not Sound  


DESCRIPTION

A situation in which the alarm is armed but does not sound when the luggage door or engine hood is opened can be caused when the body computer cannot detect whether the luggage compartment door courtesy light switch or engine hood courtesy switch is open or closed.

If the alarm does not sound, there may be a malfunction in the luggage compartment door courtesy light switch, engine hood courtesy switch, body computer or a wire harness.

WIRING DIAGRAM

E281129E01
1.385,1.615 3.25,2.021 1.865,0.406 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 1.188,3.177 3.51,3.833 2.323,0.656 10 false Luggage Compartment Door Courtesy Light Switch (Luggage Compartment Door Lock Assembly) 1.385,1.458 1.698,1.646 0.313,0.188 10 false A29 1.188,3.021 1.5,3.208 0.313,0.188 10 false L5 4.385,1.167 4.698,1.354 0.313,0.188 10 false 2D 4.385,2.688 4.698,2.875 0.313,0.188 10 false 2N 5.448,1.167 5.76,1.354 0.313,0.188 10 false MB 5.448,2.688 5.76,2.875 0.313,0.188 10 false MB 5.781,1.167 6.198,1.365 0.417,0.198 10 false HCTY 5.781,2.677 6.198,2.875 0.417,0.198 10 false LGCY 2.885,2.594 3.198,2.781 0.313,0.188 10 false 3 1.573,2.594 1.885,2.781 0.313,0.188 10 false 2 1.563,1.052 1.875,1.24 0.313,0.188 10 false 2 2.875,1.052 3.188,1.24 0.313,0.188 10 false 1 2.573,2.594 2.823,2.781 0.25,0.188 10 false D+ 1.75,2.594 2.115,2.771 0.365,0.177 10 false ACT- 4.438,0.99 4.75,1.177 0.313,0.188 10 false 9 4.417,2.51 4.729,2.729 0.313,0.219 10 false 3 5.469,2.51 5.781,2.729 0.313,0.219 10 false 21 5.469,0.99 5.781,1.208 0.313,0.219 10 false 20 4.344,3.521 5.563,3.906 1.219,0.385 10 false Driver Side Junction Block Assembly 5.74,3.802 6.74,4.042 1,0.24 10 false Body Computer

PROCEDURE

1.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

Close all doors, the luggage compartment door and the engine hood.


b.

Lock the doors using the wireless operation or entry operation*1.

*1: w/ Smart Entry and Start System



c.

Check that the security indicator light illuminates.


d.

After 30 seconds have elapsed, check that the security indicator light changes from illuminated to flashing.


HINT:

The illumination status of the security indicator light can be used to determine whether the theft deterrent system is set or unset.


Result:
Proceed to
OK
NG



OK

2.CHECK THEFT DETERRENT SYSTEM OPERATION

NG

2.CHECK THEFT DETERRENT SYSTEM OPERATION
a.

Open the driver side window.


b.

Set the theft deterrent system.

i.

Close all doors, the luggage compartment door and the engine hood.


ii.

Lock the doors using wireless operation or entry operation*1.

*1: w/ Smart Entry and Start System



iii.

Wait for 30 seconds or more.


iv.

After 30 seconds have elapsed, open the luggage compartment door or engine hood.

NOTICE:

Opening any of the doors will cause the alarm to sound, so do not open or close the doors.




Result:
Result Proceed to
Alarm does not sound when luggage compartment door is opened. A
Alarm does not sound when engine hood is opened. B



A

3.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY

B

6.INSPECT HOOD LOCK ASSEMBLY
3.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY
a.

Remove the luggage compartment door lock assembly.

Click hereVehicle Interior>LIGHTING (INT)>BACK DOOR COURTESY SWITCH(for Sedan)>REMOVAL


b.

Inspect the luggage compartment door lock assembly.

Click hereVehicle Interior>LIGHTING (INT)>BACK DOOR COURTESY SWITCH(for Sedan)>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPLACE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the L5 luggage compartment door lock assembly connector.


b.

Disconnect the 2N driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L5-3 (D+) - 2N-3 Always Below 1 Ω
L5-2 (ACT-) - Body ground Always Below 1 Ω
L5-3 (D+) or 2N-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

b.

Disconnect the driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

B343154C09
2.552,0.635 2.833,0.854 0.281,0.219 5.583,0.479 5.865,0.698 0.281,0.219 2.042,1.448 1.948,1.156 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 2.573,0.656 2.885,0.854 0.313,0.198 10 false MB 5.615,0.521 5.927,0.719 0.313,0.198 10 false 2N 1.875,1.469 2.365,1.656 0.49,0.188 10 false LGCY
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
2N-3 - MB-21 (LGCY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

6.INSPECT HOOD LOCK ASSEMBLY


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A29 hood lock assembly connector.


b.

Disconnect the 2D driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-1 - 2D-9 Always Below 1 Ω
A29-2 - Body ground Always Below 1 Ω
A29-1 or 2D-9 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

b.

Disconnect the driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

B343149C07
2.177,0.417 2.5,0.625 0.323,0.208 5.552,0.229 5.875,0.438 0.323,0.208 1.625,1.208 1.573,0.948 true 0.271,0.156 0.583,0.354 0.313,0.198 10 false *a 5.594,0.271 5.906,0.469 0.313,0.198 10 false 2D 2.219,0.438 2.531,0.635 0.313,0.198 10 false MB 1.448,1.26 2.063,1.458 0.615,0.198 10 false HCTY
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
2D-9 - MB-20 (HCTY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY