Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052750 K411 CVT _0254682 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The CVT fluid temperature sensor converts the fluid temperature into a resistance value which is detected by the ECM.

The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies voltage to the temperature sensor through ECM terminal THO1 and calculates the fluid temperature based on the voltage signal.

HINT:

The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in traffic.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input There is a short in the CVT fluid temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (CVT fluid temperature sensor)

·

ECM


Comes on DTC stored
P0713 Transmission Fluid Temperature Sensor "A" Circuit High Input Either one of the following conditions is met (1 trip detection logic):
·

When 10 seconds or more have elapsed after engine start (engine coolant and intake air temperatures at engine start were higher than -29.375°C (-20.875°F), there is an open in the CVT fluid temperature sensor circuit for more than 0.5 seconds.

·

When 15 minutes or more have elapsed after engine start (engine coolant and intake air temperatures were lower than -29.375°C (-20.875°F) at engine start, there is an open in the CVT fluid temperature sensor circuit for 0.5 seconds.


·

Wire harness or connector

·

Continuously variable transaxle assembly (CVT fluid temperature sensor)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the ECM determines the CVT fluid temperature and detects an open or short circuit in the CVT fluid temperature circuit. If the resistance value of the CVT fluid temperature is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the CVT fluid temperature sensor or wiring. The ECM illuminates the MIL and stores a DTC.

*1: 150°C (302°F) or more is indicated regardless of the actual CVT fluid temperature.

*2: -40°C (-40°F) is indicated regardless of the actual CVT fluid temperature.

HINT:

The CVT fluid temperature can be checked on the GTS display.


WIRING DIAGRAM

C279796E05
5.385,0.906 5.844,1.104 0.458,0.198 10 false THO1 1.271,1.094 3.208,1.365 1.938,0.271 10 false CVT Fluid Temperature Sensor 3.5,1.365 3.74,1.573 0.24,0.208 10 false E2 3.771,0.771 4.229,0.969 0.458,0.198 10 false 1 3.771,1.365 4.229,1.563 0.458,0.198 10 false 6 5.146,0.792 5.365,0.979 0.219,0.188 10 false 20 5.594,2.115 6.052,2.313 0.458,0.198 10 false B48 5.385,1.479 5.844,1.677 0.458,0.198 10 false ETHO 5.604,2.302 6.063,2.5 0.458,0.198 10 false ECM 0.948,2.042 1.406,2.24 0.458,0.198 10 false B54 0.969,2.219 3.542,2.688 2.573,0.469 10 false Transmission Wire (Continuously Variable Transaxle Assembly) 5.146,1.385 5.375,1.542 0.229,0.156 10 false 21 3.396,0.771 3.854,0.969 0.458,0.198 10 false THO

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (A/T OIL TEMPERATURE 1)
a.

Warm up the engine.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Temperature 1
50003 234 406

f.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 CVT fluid temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

After stall speed test: Approx. 100°C (212°F)

·

Equal to ambient temperature after cold soak


If the value is -40°C (-40°F) or 150°C (302°F) or higher, the CVT fluid temperature sensor circuit is open or shorted.

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

2.INSPECT CVT FLUID TEMPERATURE SENSOR (TRANSMISSION WIRE)

B

4.REPLACE ECM
2.INSPECT CVT FLUID TEMPERATURE SENSOR (TRANSMISSION WIRE)
a.
C225476C35
2.354,0.938 2.74,0.469 true 2.333,1.281 2.771,1.792 true 0.094,0.073 0.313,0.25 0.219,0.177 10 false *a 2.76,0.375 3.125,0.542 0.365,0.167 10 false THO 2.823,1.698 3.188,1.865 0.365,0.167 10 false E2
*a Component without harness connected
(Transmission Wire)


Disconnect the B54 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (THO) - 6 (E2) Always 79 Ω to 156 kΩ
1 (THO) - Body ground Always 10 kΩ or higher
6 (E2) - Body ground Always 10 kΩ or higher


HINT:

If the resistance is outside the specified range at either of the CVT fluid temperatures shown in the table below, the driveability of the vehicle may be affected.

CVT Fluid Temperature Specified Condition
10°C (50°F) 5.6 to 7.3 kΩ
25°C (77°F) 3.5 kΩ
110°C (230°F) 0.22 to 0.27 kΩ



c.

Connect the B54 transmission wire connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the ECM connector.


b.
C342253C01
1.5,0.271 2,0.5 0.5,0.229 1.448,2.979 1.865,2.563 true 2.365,2.969 1.948,2.552 true 0.979,2.865 1.594,3.063 0.615,0.198 10 false ETHO 2.469,2.896 3.083,3.094 0.615,0.198 10 false THO1 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.604,0.302 2.063,0.5 0.458,0.198 10 false B48
*a Rear view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-20 (THO1) - B48-21 (ETHO) Always 79 Ω to 156 kΩ
B48-20 (THO1) - Body ground Always 10 kΩ or higher
B48-21 (ETHO) - Body ground Always 10 kΩ or higher



c.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT