1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
3.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
4.REMOVE FRONT WHEELS
51442C
5.REMOVE ENGINE UNDER COVER LH (w/o Metal Type Under Cover)
51441C
6.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)
51451A
7.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)
51405A
8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)
9.DRAIN ENGINE COOLANT
10.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID
Click hereDrivetrain>K411 CVT>OIL PAN>REMOVAL
17880
11.REMOVE AIR CLEANER HOSE ASSEMBLY
12.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
17801
13.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17701
14.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
28800
15.REMOVE BATTERY
74431
16.REMOVE BATTERY TRAY
74410
17.REMOVE BATTERY CARRIER ASSEMBLY
58910C
18.REMOVE REAR CONSOLE BOX ASSEMBLY
33820B
19.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
20.SECURE STEERING WHEEL
45259A
21.REMOVE COLUMN HOLE COVER SILENCER SHEET
45260
22.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45025D
23.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
57533B
24.REMOVE FRONT FLOOR CENTER BRACE
17410
25.REMOVE FRONT EXHAUST PIPE ASSEMBLY
43498A
26.REMOVE NO. 1 DRIVE SHAFT HEAT INSULATOR
27.REMOVE FRONT DRIVE SHAFT ASSEMBLIES
28100
28.REMOVE STARTER ASSEMBLY
11363A
29.REMOVE FLYWHEEL HOUSING SIDE COVER
35141F
30.SEPARATE NO. 1 BREATHER PLUG
Disengage the clamp and separate the No. 1 breather plug from the hose clamp.
16260
31.DISCONNECT WATER BY-PASS HOSE ASSEMBLY
Slide the 2 hose clips and disconnect the 2 water by-pass hoses from the transmission oil cooler.
Disengage the 2 clamps to separate the water by-pass hose assembly from the continuously variable transaxle assembly.
82121
32.DISCONNECT ENGINE WIRE
Disconnect the 6 connectors from the continuously variable transaxle assembly.
Disengage the 8 clamps to separate the engine wire from the continuously variable transaxle assembly.
Remove the bolt to separate the engine wire from the continuously variable transaxle assembly.
Remove the bolt and wire harness clamp bracket from the continuously variable transaxle assembly.
32101A
33.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Using SST, hold the crankshaft pulley.
Remove the 6 drive plate and torque converter assembly setting bolts.
34.SUPPORT ENGINE ASSEMBLY
| *a | Attachment |
| *b | Engine Lifter |
|
Attachment Placement Positions |
Place the height adjustment attachments or plate lift attachments in the positions shown in the illustration and set the engine lifter underneath the engine assembly.
Place the height adjustment attachments or plate lift attachments so that the engine assembly with the continuously variable transaxle assembly is level.
As the engine assembly with the continuously variable transaxle assembly is very heavy, be sure to support it securely.
To prevent deformation of the oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the engine assembly.
To prevent deformation of the transaxle oil pan sub-assembly, never set any attachments against the transaxle oil pan sub-assembly.
51201
35.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
12364B
36.REMOVE NO. 2 ENGINE MOVING CONTROL ROD
Remove the 3 bolts and No. 2 engine moving control rod from the continuously variable transaxle assembly.
30400
37.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
| *a | Transmission Jack |
| *b | Lashing Belt |
|
Attachment Placement Positions |
Set the attachments in the positions shown in the illustration and set the transmission jack underneath the continuously variable transaxle assembly.
To prevent deformation of the transaxle oil pan sub-assembly, never set any attachments against the transaxle oil pan sub-assembly.
Secure the continuously variable transaxle assembly to the transmission jack with a lashing belt, etc., to prevent the continuously variable transaxle assembly from falling.
Remove the bolt and nut, and separate the engine mounting bracket LH from the engine mounting insulator LH.
Turn the bolt while holding the nut.
Remove the 5 bolts and engine mounting insulator LH from the body.
Remove the 4 bolts and engine mounting bracket LH from the continuously variable transaxle assembly.
Remove the 8 bolts and continuously variable transaxle assembly from the engine assembly.
Make sure that the engine assembly is not tilted.
To prevent damage to the knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.
Do not allow the torque converter assembly to fall off.
Bolt A: Remove from continuously variable transaxle assembly side
Bolt B: Remove from engine assembly side
32000A
38.REMOVE TORQUE CONVERTER ASSEMBLY
Remove the torque converter assembly from the continuously variable transaxle assembly.
Remove the torque converter assembly from the input shaft horizontally.
30400E
39.REMOVE CVT OIL PUMP TYPE T OIL SEAL
Do not remove the front oil pump assembly from the CVT main body, as there is the possibility of the entry of dust and foreign matter.
Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which may prevent the vehicle from being driven, may occur if dust or fine foreign matter enters the CVT.
Do not use cotton work gloves, cloths, paper towels, etc. that may produce lint, dust or foreign matter.
Perform the operation as quickly as possible, as dust and foreign matter may enter the CVT while the torque converter assembly is not attached to it.
Do not use an air gun until the torque converter assembly has been installed, as it may cause dust and foreign matter to be stirred up.
Clean the tips of both the claws of SST and the center bolt.
Using SST, remove the CVT oil pump type T oil seal from the continuously variable transaxle assembly.
Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles may be produced if they do.
33823
40.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.
41.REMOVE WIRE HARNESS CLAMP BRACKET
Disengage the breather hose clamp and separate the breather plug hose from the wire harness clamp bracket.
Remove the 5 bolts and 4 wire harness clamp brackets from the continuously variable transaxle assembly.
35141D
42.REMOVE BREATHER PLUG HOSE
Perform this procedure only when replacement of the breather plug hose is necessary.
| *1 | No. 1 Breather Plug |
| *2 | Breather Plug Hose |
| *3 | Breather Hose Clamp |
Disengage the clamp and remove the breather hose clamp from the breather plug hose.
Remove the breather plug hose with the No. 1 breather plug from the continuously variable transaxle assembly.
Remove the No. 1 breather plug from the breather plug hose.
32000A
43.INSPECT TORQUE CONVERTER ASSEMBLY
44.INSPECT DRIVE PLATE