Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052750 K411 CVT _0254682 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0717  Input/Turbine Speed Sensor "A" Circuit No Signal  P07BF  Input/Turbine Speed Sensor "A" Circuit Low  P07C0  Input/Turbine Speed Sensor "A" Circuit High  


DESCRIPTION

The ECM receives a signal from the turbine speed sensor (transmission revolution sensor (NT)) installed in the continuously variable transaxle to control the lock-up engagement pressure and forward and reverse clutch pressure.

The transmission revolution sensor (NT) detects the continuously variable transaxle input shaft speed and sends a signal to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0717 Input/Turbine Speed Sensor "A" Circuit No Signal All of the following conditions are met (1 trip detection logic):
·

Vehicle is driven with the shift lever in D

·

Output shaft speed is 300 rpm or more

·

No malfunctions are found in the park/neutral position switch

·

Input turbine speed indicated by the transmission revolution sensor (NT) is less than 300 rpm for 2 seconds


·

Wire harness or connector

·

Continuously variable transaxle assembly (Transmission revolution sensor (NT))

·

ECM


Comes on DTC stored
P07BF Input/Turbine Speed Sensor "A" Circuit Low There is no malfunction in transmission revolution sensor (NT) signals, and the transmission revolution sensor (NT) output voltage is less than 0.1 V for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Transmission revolution sensor (NT))

·

ECM


Comes on DTC stored
P07C0 Input/Turbine Speed Sensor "A" Circuit High There is no malfunction in transmission revolution sensor (NT) signals, and the transmission revolution sensor (NT) output voltage is higher than 1.9 V for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (Transmission revolution sensor (NT))

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The turbine speed sensor (transmission revolution sensor (NT)) detects the transaxle input shaft speed. The ECM determines the necessary gear ratio based on a comparison of the turbine speed sensor (input shaft speed) with the output speed sensor (output shaft speed).

When the output shaft speed is higher than the expected value and the input shaft speed is less than 300 rpm while driving with the shift lever in D, the ECM will determine that there is a malfunction in the transmission revolution sensor (NT). The ECM will illuminate the MIL and store this DTC.

WIRING DIAGRAM

C277072E14
0.854,3.01 3.219,3.25 2.365,0.24 10 false Transmission Revolution Sensor (NT) 2.75,1.104 2.99,1.333 0.24,0.229 10 false 1 2.74,2.104 2.979,2.333 0.24,0.229 10 false 2 5.313,1.135 5.708,1.333 0.396,0.198 10 false 19 5.604,2.219 6,2.417 0.396,0.198 10 false NTB 5.604,1.24 6,1.438 0.396,0.198 10 false NTO 0.865,2.781 1.26,2.979 0.396,0.198 10 false B21 5.323,2.094 5.719,2.292 0.396,0.198 10 false 29 5.792,3.188 6.188,3.385 0.396,0.198 10 false ECM 5.802,3 6.198,3.198 0.396,0.198 10 false B48 2.375,1.156 2.771,1.354 0.396,0.198 10 false NTO 2.375,2.115 2.771,2.313 0.396,0.198 10 false NTB

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (SPD (NT) AND NT SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
SPD (NT)
NT Sensor Voltage
50003 234 390,391

e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NT) Input turbine speed Min.: 0 rpm
Max.: 12750 rpm
·

Lock-up on (After warming up engine): Input turbine speed (NT) equal to engine speed

·

Lock-up off (Idling with shift lever in P or N): Input turbine speed (NT) nearly equal to engine speed

·

Vehicle stopped with shift lever in R: 0 rpm


Data is displayed in increments of 50 rpm.
NT Sensor Voltage Input turbine speed (NT) sensor output voltage Min.: 0 V
Max.: 4.999 V
Engine idling (Vehicle stopped with shift lever in P or N): 0.6 to 1.5 V -

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

B

4.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
a.

Remove the transmission revolution sensor (NT).

Click hereDrivetrain>K411 CVT>REVOLUTION SENSOR>REMOVAL


b.

Connect the battery to the sensor as shown in the illustration.

C154686C68
4.802,0.385 6.844,2.406 2.042,2.021 2.906,0.333 3.219,0.188 false 2.229,0.688 2.542,0.542 false 5.333,2 5.563,1.563 true 6.25,2 6.063,1.573 true 0.667,0.281 0.906,0.448 0.24,0.167 10 false *b 2.125,0.615 2.25,0.792 0.125,0.177 10 false 2 3.26,0.083 3.385,0.26 0.125,0.177 10 false 1 0.635,1.458 0.823,1.625 0.188,0.167 10 false *1 2.625,2.094 2.813,2.302 0.188,0.208 10 false *c 3.542,1.802 3.729,2.01 0.188,0.208 10 false *a 4.885,0.458 5.073,0.667 0.188,0.208 10 false *d 6.135,2 6.594,2.198 0.458,0.198 10 false NTO 5.177,2 5.635,2.198 0.458,0.198 10 false NTB
*1 Battery - -
*a Magnet *b Ammeter
*c 5 mm or less *d Component without harness connected
(Transmission Revolution Sensor (NT))



c.

Wave a magnetic object left and right in front of the transmission revolution sensor (NT) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



d.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NTO) - 2 (NTB) Low signal 4 to 8 mA
1 (NTO) - 2 (NTB) High signal 12 to 16 mA



e.

Install the transmission revolution sensor (NT).


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NT)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)
a.

Disconnect the B21 transmission revolution sensor (NT) connector.


b.

Disconnect the B48 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B21-1 (NTO) - B48-19 (NTO) Always Below 1 Ω
B21-2 (NTB) - B48-29 (NTB) Always Below 1 Ω
B21-1 (NTO) or B48-19 (NTO) - Body ground Always 10 kΩ or higher
B21-2 (NTB) or B48-29 (NTB) - Body ground Always 10 kΩ or higher



d.

Connect the B21 ECM connector.


e.

Connect the B48 transmission revolution sensor (NT) connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT