Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052750 K411 CVT _0254682 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0722  Output Speed Sensor Circuit No Signal  P077C  Output Speed Sensor Circuit Low  P077D  Output Speed Sensor Circuit High  


DESCRIPTION

The ECM receives a signal from the secondary pulley speed sensor (transmission revolution sensor (NOUT)) installed in the continuously variable transaxle and determines the output shaft speed in order to control the gear ratio.

The transmission revolution sensor (NOUT) detects the continuously variable transaxle output shaft speed and sends a signal to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0722 Output Speed Sensor Circuit No Signal All of the following conditions are met (1 trip detection logic):
·

Vehicle is driven with the shift lever in D

·

Output shaft speed is 300 rpm or more

·

No malfunctions are found in the park/neutral position switch

·

Output shaft speed indicated by the transmission revolution sensor (NOUT) is less than 300 rpm for 2 seconds


·

Wire harness or connector

·

Transmission revolution sensor (NOUT)

·

ECM


Comes on DTC stored
P077C Output Speed Sensor Circuit Low There is no malfunction in transmission revolution sensor (NOUT) signals, and the transmission revolution sensor (NOUT) output voltage is less than 0.1 V for 2 seconds (1 trip detection logic)
·

Wire harness or connector

·

Transmission revolution sensor (NOUT)

·

ECM


Comes on DTC stored
P077D Output Speed Sensor Circuit High There is no malfunction in transmission revolution sensor (NOUT) signals, and the transmission revolution sensor (NOUT) output voltage is higher than 1.9 V for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NOUT)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM receives a signal from the secondary pulley speed sensor (transmission revolution sensor (NOUT)) installed in the continuously variable transaxle and determines the output shaft speed in order to control the gear ratio.

If the ECM detects no signal from the secondary pulley speed sensor (transmission revolution sensor (NOUT)) even while the vehicle is moving, it will determine that there is a malfunction in the secondary pulley speed sensor (transmission revolution sensor (NOUT)). The ECM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

C277072E15
0.719,3.01 3.302,3.26 2.583,0.25 10 false Transmission Revolution Sensor (NOUT) 2.229,1.125 2.74,1.344 0.51,0.219 10 false NOTO 2.229,2.083 2.771,2.292 0.542,0.208 10 false NOTB 2.76,1.115 3,1.344 0.24,0.229 10 false 1 2.75,2.094 2.99,2.323 0.24,0.229 10 false 2 5.375,1.115 5.771,1.313 0.396,0.198 10 false 9 5.604,2.219 6.094,2.438 0.49,0.219 10 false NOTB 5.604,1.24 6.125,1.458 0.521,0.219 10 false NOTO 0.729,2.781 1.125,2.979 0.396,0.198 10 false B51 5.302,2.104 5.698,2.302 0.396,0.198 10 false 10 5.792,3.188 6.188,3.385 0.396,0.198 10 false ECM 5.802,3 6.198,3.198 0.396,0.198 10 false B47

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (SPD (NOUT) AND NOUT SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
SPD (NOUT)
NOUT Sensor Voltage
50003 234 402,403

e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NOUT) Secondary pulley speed (NOUT) Min.: 0 rpm
Max.: 12750 rpm
·

Vehicle stopped: 0 rpm

·

Vehicle cruising at approx. 60 km/h (37 mph): 2975 rpm


Data is displayed in increments of 50 rpm.
NOUT Sensor Voltage Secondary pulley speed (NOUT) sensor output voltage Min.: 0.000 V
Max.: 4.999 V
Engine idling: Approximately 2 V -

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)

B

4.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)
a.

Remove the transmission revolution sensor (NOUT).

Click hereDrivetrain>K411 CVT>REVOLUTION SENSOR>REMOVAL


b.

Connect the battery to the sensor as shown in the illustration.

C173707C21
4.865,0.365 6.792,2.438 1.927,2.073 1.667,1.229 1.938,1.031 false 2.49,0.615 2.198,0.833 false 5.292,2.115 5.646,1.583 true 6.365,2.115 6.01,1.583 true 4.938,0.438 5.156,0.656 0.219,0.219 10 false *d 0.625,1.688 0.865,1.896 0.24,0.208 10 false *1 1.542,1.146 1.677,1.344 0.135,0.198 10 false 2 2.531,0.5 2.667,0.698 0.135,0.198 10 false 1 5.094,2.115 5.563,2.323 0.469,0.208 10 false NOTB 6.208,2.125 6.698,2.333 0.49,0.208 10 false NOTO 0.646,0.51 0.854,0.688 0.208,0.177 10 false *b 2.958,2.125 3.156,2.313 0.198,0.188 10 false *c 3.865,1.792 4.083,1.99 0.219,0.198 10 false *a
*1 Battery - -
*a Magnet *b Ammeter
*c 5 mm or less *d Component without harness connected
(Transmission Revolution Sensor (NOUT))



c.

Wave a magnetic object left and right in front of the transmission revolution sensor (NOUT) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



d.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NOTO) - 2 (NOTB) Low signal 4 to 8 mA
1 (NOTO) - 2 (NOTB) High signal 12 to 16 mA



e.

Install the transmission revolution sensor (NOUT).


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NOUT) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NOUT)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NOUT) - ECM)
a.

Disconnect the B51 transmission revolution sensor (NOUT) connector.


b.

Disconnect the B47 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-1 (NOTO) - B47-9 (NOTO) Always Below 1 Ω
B51-2 (NOTB) - B47-10 (NOTB) Always Below 1 Ω
B51-1 (NOTO) or B47-9 (NOTO) - Body ground Always 10 kΩ or higher
B51-2 (NOTB) - B47-10 (NOTB) - Body ground Always 10 kΩ or higher



d.

Connect the B47 ECM connector.


e.

Connect the B51 transmission revolution sensor (NOUT) connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT