Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052750 K411 CVT _0254682 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0962  Pressure Control Solenoid "A" Control Circuit Low (Shift Solenoid Valve DS1)  P0963  Pressure Control Solenoid "A" Control Circuit High (Shift Solenoid Valve DS1)  P0966  Pressure Control Solenoid "B" Control Circuit Low (Shift Solenoid Valve DS2)  P0967  Pressure Control Solenoid "B" Control Circuit High (Shift Solenoid Valve DS2)  


DESCRIPTION

Using shift solenoid valve DS1 (inflow to the primary pulley) and shift solenoid valve DS2 (outflow from the primary pulley), the ECM controls the line pressure and fluid volume input to and output to the primary pulley according to the vehicle speed and accelerator pedal angle. As a fail-safe function, if a solenoid is shorted or open, the ECM stops current to the faulty solenoid.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0962 Pressure Control Solenoid "A" Control Circuit Low (Shift Solenoid Valve DS1) When the vehicle is driven so that gear ratio changes occur, there is a short circuit in the shift solenoid valve DS1 circuit for 20 times (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored
P0963 Pressure Control Solenoid "A" Control Circuit High (Shift Solenoid Valve DS1) When the vehicle is driven so that gear ratio changes occur, there is an open circuit in the shift solenoid valve DS1 circuit for 20 times (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored
P0966 Pressure Control Solenoid "B" Control Circuit Low (Shift Solenoid Valve DS2) When the vehicle is driven so that gear ratio changes occur, there is a short circuit in the shift solenoid valve DS2 circuit for 20 times (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored
P0967 Pressure Control Solenoid "B" Control Circuit High (Shift Solenoid Valve DS2) When the vehicle is driven so that gear ratio changes occur, there is an open circuit in the shift solenoid valve DS2 circuit for 20 times (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve DS1 or DS2 circuit. When there is an open or short circuit in the shift solenoid valve circuits, the ECM detects the problem, illuminates the MIL and stores a DTC.

WIRING DIAGRAM

C277074E07
0.229,4.104 4.26,4.354 4.031,0.25 10 false Transmission Wire (Continuously Variable Transaxle Assembly) 0.24,3.875 0.615,4.083 0.375,0.208 10 false B54 1.521,2.854 3.229,3.083 1.708,0.229 10 false Shift Solenoid Valve DS2 1.521,1.677 3.229,1.906 1.708,0.229 10 false Shift Solenoid Valve DS1 3.208,1.104 3.583,1.313 0.375,0.208 10 false DS1 3.208,2.271 3.583,2.479 0.375,0.208 10 false DS2 3.625,1.104 4,1.313 0.375,0.208 10 false 10 3.667,2.271 4.042,2.479 0.375,0.208 10 false 5 5.292,1.115 5.667,1.323 0.375,0.208 10 false 11 5.302,2.302 5.677,2.51 0.375,0.208 10 false 10 5.615,1.24 5.99,1.448 0.375,0.208 10 false DS1 5.615,2.417 5.99,2.625 0.375,0.208 10 false DS2 5.813,4.208 6.188,4.417 0.375,0.208 10 false ECM 5.823,4 6.198,4.208 0.375,0.208 10 false B48

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE SHIFT POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Shift Position
Data List Display
Shift Status
50004 234 116 416

e.

In accordance with the display on the GTS, perform the Active Test.

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Shift Position Operate the shift solenoid valves to allow the gear ratio to be manually selected [1st (gear ratio max.) - 2nd - 3rd - 4th - 5th (gear ratio min.)]
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Used to check the operation of the shift solenoid valves.
HINT:

Perform "Control the Shift Position" while monitoring "Shift Status" to confirm actual gear position.


NOTICE:

Performing this test at speeds other than those specified in "Vehicle Condition" will damage the transaxle.


[Vehicle Condition]
Perform at a vehicle speed of 20 km/h (12 mph) or more and 45 km/h (28 mph) or less.

Result:
Result Proceed to
Gear ratio does not change A
Gear ratio changes B



A

2.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE DS1 AND DS2)

B

4.REPLACE ECM
2.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE DS1 AND DS2)
a.
C225476C36
1.031,0.948 0.74,0.552 true 1.031,1.25 0.688,1.656 true 0.094,0.042 0.313,0.219 0.219,0.177 10 false *a 0.417,0.458 0.823,0.635 0.406,0.177 10 false DS2 0.406,1.563 0.813,1.76 0.406,0.198 10 false DS1
*a Component without harness connected
(Transmission Wire)


Disconnect the B54 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (DS2) - Body ground 20°C (68°F) 11 to 13 Ω
10 (DS1) - Body ground 20°C (68°F) 11 to 13 Ω



c.

Connect the B54 transmission wire connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the ECM connector.


b.
C342253C02
1.479,0.333 1.969,0.583 0.49,0.25 1.125,2.896 1.875,2.479 true 2.333,3.083 1.948,2.469 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.573,0.365 2.031,0.563 0.458,0.198 10 false B48 0.74,2.802 1.198,3 0.458,0.198 10 false DS1 2.385,2.979 2.844,3.177 0.458,0.198 10 false DS2
*a Rear view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-11 (DS1) - Body ground 20°C (68°F) 11 to 13 Ω
B48-10 (DS2) - Body ground 20°C (68°F) 11 to 13 Ω



c.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT