Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.04–2016.07
RM30M0E _52 Drivetrain _052750 K411 CVT _0254682 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1586  Acceleration Sensor Malfunction  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the deceleration sensor. If a malfunction is determined in the deceleration sensor based on a malfunction signal from the brake actuator assembly (skid control ECU).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1586 Acceleration Sensor Malfunction After the ignition switch is turned ON, the brake actuator assembly (skid control ECU) has detected either one of the following conditions, and the ECM has received a diagnostic signal from the brake actuator assembly (skid control ECU) for 3 seconds or more (1 trip detection logic).
·

While the vehicle is driven at 30 km/h (19 mph) or more, the difference between the calculated longitudinal G calculated based on the G sensor value and longitudinal G calculated based on the vehicle speed exceeds 0.35 G for 60 seconds or more.

·

The deceleration sensor signal does not change 16 times or more while the vehicle speed decreases from 30 km/h (19 mph) to 0 km/h (0 mph).


·

Deceleration sensor

·

Brake actuator assembly (Skid control ECU)

·

CAN communication system


Does not come on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)
a.

Check for DTCs of the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK DTC OUTPUT (IN ADDITION TO DTC P1586)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK DTC OUTPUT (IN ADDITION TO DTC P1586)
a.

Connect the GTS to the DLC3.


b.

Turn the GTS on.


c.

Turn the ignition switch to ON.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Perform a road test where the vehicle is driven at 30 km/h (18 mph) or more, the brakes are applied at least 16 times and the vehicle is finally stopped.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

g.

Read the DTCs using the GTS.

HINT:

If any DTCs other than P1586 are output, perform troubleshooting for those DTCs first.



Result:
Result Proceed to
Only DTC P1586 is output A
DTC P1586 and other DTCs are output B



A

3.READ VALUE USING GTS (G SENSOR)

B

3.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410

e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of deceleration sensor Min.: 0 V
Max.: 79.998 V
Displays converted voltage of deceleration sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

4.REPLACE DECELERATION SENSOR

B

5.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
4.REPLACE DECELERATION SENSOR

Result:
Proceed to
NEXT



NEXT

5.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
a.

Replace the brake actuator assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


Result:
Proceed to
NEXT



NEXT