The ECM stores DTC P1589 if deceleration sensor zero point calibration is not performed or failed after system components such as the ECM are replaced.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1589 | Acceleration Sensor Learning Value | Either one of the following conditions is met (1 trip detection logic):
·
When the vehicle speed is 2 km/h (1.2 mph) or more, Deceleration Sensor Zero Point Calibration has not been completed. ·
While Deceleration Sensor Zero Point Calibration is performed, the learned values of Deceleration Sensor Zero Point Calibration are abnormal (out of normal range). |
·
Deceleration sensor zero point calibration has not been performed ·
Vehicle was not stabilized during deceleration sensor zero point calibration ·
Deceleration sensor ·
ECM |
Does not come on | DTC stored |
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
If the CVT oil pressure calibration is performed before the deceleration sensor zero point calibration, DTC P1589 is stored. In this case, perform the steps below to return the system to normal.
Always perform calibration with the vehicle on level ground (Inclination: 0+/-0.25°).
Do not shake or vibrate the vehicle during calibration.
Turn the ignition switch off.
Move the shift lever to P and apply the parking brake.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.
| Tester Display |
|---|
| Reset Memory |
Enter the following menus: Powertrain / ECT / Utility / Deceleration Sensor Zero Point Calibration.
| Tester Display |
|---|
| Deceleration Sensor Zero Point Calibration |
When "Complete" is displayed on the screen, deceleration sensor zero point calibration is complete.
If "Error" is displayed on the screen and DTC P1589 is output (confirm the DTC detection conditions), the deceleration sensor circuit may be malfunctioning.
Shaking or vibrating the vehicle during deceleration sensor zero point calibration may cancel calibration. If "Error" is displayed on the screen and DTC P1589 is not output, perform step calibration again.
If "Error" is displayed on the GTS, read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| Deceleration sensor zero point calibration is completed normally | A |
| DTC P1589 is output | B |
A
B
Do not clear the learned values by performing Reset Memory.
Turn the ignition switch off and wait at least 30 seconds.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait at least 2 seconds.
Do not start the engine.
CVT oil pressure calibration is performed with the ignition switch ON (engine stopped). However, calibration cannot be performed under the following conditions:
Oil pressure sensor value is 0.065 MPa (0.663 kgf/cm2, 9.43 psi) or more.
CVT oil temperature is 0°C (32°F) or less or 120°C (212°F) or more.
Enter the following menus: Powertrain / Engine and ECT / Utility.
Start the engine and wait at least 5 seconds.
Start the engine with the shift lever in P.
After starting the engine, do not operate the accelerator pedal.
Enter the following menus: Powertrain / Engine and ECT / Utility / CVT Oil Pressure Calibration
During CVT oil pressure calibration, the engine idle speed will increase.
When "Complete" is displayed on the screen, CVT oil pressure calibration is complete.
The learned values cannot be cleared by only disconnecting and reconnecting the cable to the negative (-) battery terminal.
| Tester Display |
|---|
| CVT Oil Pressure Calibration |
Check for DTCs again.
| Proceed to |
|---|
| NEXT |
NEXT
Check the deceleration sensor for any inclination, bracket deformation or installation clearance.
The deceleration sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| G Sensor |
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| G Sensor | Converted output voltage of deceleration sensor | Min.: 0 V
Max.: 79.998 V |
Displays converted voltage of deceleration sensor
·
Vehicle on level ground: 2.31 V to 2.69 V ·
Decelerating: 1.88 V to 2.5 V ·
Accelerating: 2.5 V to 3.11 V ·
G sensor malfunction: Set to 1.87 V ·
Communication malfunction: Set to 1.87 V |
- |
| Result | Proceed to |
|---|---|
| Data display is not within Normal Condition range | A |
| Data display is within Normal Condition range | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the deceleration sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DECELERATION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT