Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052750 K411 CVT _0254682 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P2759  Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)  


DESCRIPTION

The ECM uses the shift solenoid valve SLU to perform lock-up control in response to the driving conditions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) While engine running, there is an open or short circuit in the shift solenoid valve SLU circuit for 1 second or more (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

When an open or short in a shift solenoid valve SLU circuit is detected, the ECM determines there is a malfunction. The ECM will turn on the MIL and store this DTC.

WIRING DIAGRAM

C251557E66
5.792,3 6.156,3.198 0.365,0.198 10 false B48 5.792,3.198 6.188,3.417 0.396,0.219 10 false ECM 0.344,2.74 0.708,2.938 0.365,0.198 10 false B54 0.333,2.958 4.375,3.229 4.042,0.271 10 false Transmission Wire (Continuously Variable Transaxle Assembly) 5.615,1.26 6.094,1.469 0.479,0.208 10 false SLU+ 5.625,2.229 6.063,2.448 0.438,0.219 10 false SLU- 5.375,1.125 5.625,1.365 0.25,0.24 10 false 2 5.375,2.094 5.656,2.354 0.281,0.26 10 false 1 3.906,1.146 4.115,1.344 0.208,0.198 10 false 4 3.917,2.104 4.125,2.302 0.208,0.198 10 false 9 3.458,1.135 3.938,1.333 0.479,0.198 10 false SLU+ 3.448,2.083 3.927,2.313 0.479,0.229 10 false SLU- 1.51,1.74 3.219,2.01 1.708,0.271 10 false Shift Solenoid Valve SLU

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)
a.
C225476C38
1.354,0.958 1.021,0.531 true 1.354,1.25 0.927,1.833 true 0.094,0.042 0.313,0.219 0.219,0.177 10 false *a 0.615,0.438 1.031,0.635 0.417,0.198 10 false SLU+ 0.542,1.74 0.948,1.938 0.406,0.198 10 false SLU-
*a Component without harness connected
(Transmission Wire)


Disconnect the B54 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (SLU+) - 9 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
4 (SLU+) - Body ground Always 10 kΩ or higher
9 (SLU-) - Body ground Always 10 kΩ or higher



c.

Connect the B54 transmission wire connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the ECM connector.


b.
C342253C04
1.5,0.333 2,0.583 0.5,0.25 1.083,2.75 1.958,2.375 true 2.667,3 2.083,2.375 true 0.188,0.25 0.5,0.448 0.313,0.198 10 false *a 1.594,0.365 2.052,0.563 0.458,0.198 10 false B48 0.667,2.635 1.281,2.833 0.615,0.198 10 false SLU+ 2.719,2.896 3.333,3.094 0.615,0.198 10 false SLU-
*a Rear view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-2 (SLU+) - B48-1 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
B48-2 (SLU+) - Body ground Always 10 kΩ or higher
B48-1 (SLU-) - Body ground Always 10 kΩ or higher



c.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT