Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052750 K411 CVT _0254682 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P2767  Input / Turbine Speed Sensor "B" Circuit No Signal  


DESCRIPTION

The ECM detects the input shaft speed based on the signal from the primary pulley speed sensor (transmission revolution sensor (NIN)) and performs gear ratio control.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2767 Input / Turbine Speed Sensor "B" Circuit No Signal While the vehicle is driven with the shift lever in D, and the output shaft speed is 300 rpm or more (vehicle speed is approximately 6 km/h [4 mph] or more), the speed indicated by the transmission revolution sensor (NIN) is less than 300 rpm for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NIN)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM receives a signal from the primary pulley speed sensor (transmission revolution sensor (NIN)) installed in the continuously variable transaxle and determines the input shaft speed in order to control the gear ratio. If the ECM detects no signal from the primary pulley speed sensor even while the vehicle is moving, it will determine that there is a malfunction in the primary pulley speed sensor. The ECM will illuminate the MIL and store this DTC.

WIRING DIAGRAM

C280944E06
0.792,2.958 3.188,3.198 2.396,0.24 10 false Transmission Revolution Sensor (NIN) 0.802,2.74 1.125,2.938 0.323,0.198 10 false B50 2.313,2.073 2.74,2.302 0.427,0.229 10 false NIN- 2.292,1.094 2.719,1.323 0.427,0.229 10 false NIN+ 2.75,1.115 3.073,1.313 0.323,0.198 10 false 2 2.74,2.104 3.063,2.302 0.323,0.198 10 false 1 5.625,1.24 6.052,1.469 0.427,0.229 10 false NIN+ 5.615,2.219 6.042,2.448 0.427,0.229 10 false NIN- 5.313,1.135 5.74,1.365 0.427,0.229 10 false 32 5.813,3 6.24,3.229 0.427,0.229 10 false B48 5.813,3.198 6.24,3.427 0.427,0.229 10 false ECM 5.313,2.104 5.74,2.333 0.427,0.229 10 false 31

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (SPD (NIN), ENGINE SPEED, LOCK UP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
SPD (NIN)
Lock Up
50003 234 9,400,417

e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
600 to 700 rpm: Idling When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
SPD (NIN) Primary pulley speed (NIN) Min.: 0 rpm
Max.: 12750 rpm
·

Vehicle stopped: 0 rpm

·

Lock-up on (After warming up engine): Primary pulley speed (NIN) equal to engine speed


Data is displayed in increments of 50 rpm.
Lock Up Lock-up ON or OFF
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN)

B

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN)
a.
C221276C10
0.865,1.25 1.427,1.25 true 2,1.25 2.563,1.25 true 0.177,0.219 0.365,0.406 0.188,0.188 10 false *a 0.5,1.177 0.854,1.354 0.354,0.177 10 false NIN+ 2.615,1.167 2.938,1.323 0.323,0.156 10 false NIN-
*a Component without harness connected
(Transmission Revolution Sensor (NIN))


Disconnect the B50 transmission revolution sensor (NIN) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NIN-) - 2 (NIN+) 20°C (68°F) 560 to 680 Ω



c.

Connect the B50 transmission revolution sensor (NIN) connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NIN)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM)
a.

Disconnect the ECM connector.


b.
C342253C05
1.49,0.323 1.99,0.583 0.5,0.26 1.021,3.073 1.438,2.656 true 2.5,3.167 1.51,2.656 true 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 1.604,0.365 2.063,0.563 0.458,0.198 10 false B48 0.583,3 1.198,3.198 0.615,0.198 10 false NIN+ 2.552,3.063 3.167,3.26 0.615,0.198 10 false NIN-
*a Rear view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-32 (NIN+) - B48-31 (NIN-) 20°C (68°F) 560 to 680 Ω
B48-32 (NIN+) - Body ground Always 10 kΩ or higher
B48-31 (NIN-) - Body ground Always 10 kΩ or higher



c.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT