Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052750 K411 CVT _0254682 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P282B  Pressure Control Solenoid "K" Electrical (Shift Solenoid Valve SLS)  


DESCRIPTION

The ECM uses shift solenoid valve SLS to control the secondary pulley pressure and belt clamping pressure according to the input shaft torque. Additionally, shift solenoid valve SLS is used to control the forward and reverse clutch hydraulic pressure when the forward and reverse clutch is engaged.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P282B Pressure Control Solenoid "K" Electrical (Shift Solenoid Valve SLS) While the vehicle is driven, an open or a short is detected in the shift solenoid valve SLS circuit for 1 second or more (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short circuit in the shift solenoid valve SLS circuit. When there is an open or short circuit in the shift solenoid valve SLS circuit, the ECM detects the problem, illuminates the MIL and stores this DTC.

WIRING DIAGRAM

C251557E67
5.792,3 6.156,3.198 0.365,0.198 10 false B48 5.792,3.198 6.188,3.417 0.396,0.219 10 false ECM 0.344,2.74 0.708,2.938 0.365,0.198 10 false B54 0.333,2.958 4.375,3.229 4.042,0.271 10 false Transmission Wire (Continuously Variable Transaxle Assembly) 5.615,1.26 6.094,1.469 0.479,0.208 10 false SLS+ 5.625,2.229 6.063,2.448 0.438,0.219 10 false SLS- 5.365,1.146 5.615,1.385 0.25,0.24 10 false 5 5.365,2.104 5.646,2.365 0.281,0.26 10 false 4 3.927,1.125 4.135,1.323 0.208,0.198 10 false 2 3.927,2.104 4.135,2.302 0.208,0.198 10 false 7 3.438,1.115 3.917,1.313 0.479,0.198 10 false SLS+ 3.448,2.083 3.927,2.313 0.479,0.229 10 false SLS- 1.51,1.74 3.219,2.01 1.708,0.271 10 false Shift Solenoid Valve SLS

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLS)
a.
C225476C39
2.104,0.969 2.49,0.5 true 2.115,1.271 2.552,1.781 true 0.094,0.073 0.313,0.25 0.219,0.177 10 false *a 2.521,0.427 2.885,0.594 0.365,0.167 10 false SLS+ 2.594,1.719 2.958,1.885 0.365,0.167 10 false SLS-
*a Component without harness connected
(Transmission Wire)


Disconnect the B54 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SLS+) - 7 (SLS-) 20°C (68°F) 5.0 to 5.6 Ω
2 (SLS+) - Body ground Always 10 kΩ or higher
7 (SLS-) - Body ground Always 10 kΩ or higher



c.

Connect the B54 transmission wire connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the ECM connector.


b.
C342253C06
1.5,0.25 2,0.5 0.5,0.25 1,2.854 1.667,2.354 true 2.417,3.083 1.75,2.333 true 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 1.615,0.281 2.073,0.479 0.458,0.198 10 false B48 0.552,2.74 1.167,2.938 0.615,0.198 10 false SLS+ 2.469,2.979 3.083,3.177 0.615,0.198 10 false SLS-
*a Rear view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-5 (SLS+) - B48-4 (SLS-) 20°C (68°F) 5.0 to 5.6 Ω
B48-5 (SLS+) - Body ground Always 10 kΩ or higher
B48-4 (SLS-) - Body ground Always 10 kΩ or higher



c.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT