The skid control ECU (brake actuator assembly) inputs the stop light signal and brake operation condition. When the brake pedal is depressed and the stop light switch signal is not input, C1426 is output.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1426 | Stop Light Switch OFF Stuck Malfunction | After a stuck judgement* has been made within 10 minutes of stopping the vehicle, then after driving at a speed of 35 km/h or more and then slowing to 3 km/h or less, the stuck judgement* continues. | ·
Wire harness or connector ·
Stop light switch assembly ·
Skid Control ECU (Brake actuator assembly) |
*: While the master pressure sensor output value (voltage) is 0.86 V or more, there is no stop switch signal for 5 seconds or more continuously.
Refer to DTC C1425.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Check that all the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
|---|---|
| Brake pedal depressed. | On |
| Brake pedal released. | Off |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Select the Data List using the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Tester Display |
|---|
| Stop Light SW |
Check that the stop light switch display observed on the GTS changes according to brake pedal operation.
The GTS displays ON or OFF according to brake pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Master Cylinder Sensor | Master cylinder pressure sensor reading | Min.: 0.00 V, Max.: 5.00 V | Brake pedal released: 0.30 to 0.80 V | Reading increases when brake pedal is depressed |
Data Monitor voltage is within the specified range.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Check the brake pedal height and stop light switch assembly installation.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
The brake pedal height and stop light switch assembly installation are normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *A | for Manual Transaxle |
| *B | for Continuously Variable Transaxle |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A48-2 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 8 to 14 V |
| Stop light switch OFF (Brake pedal released) | Below 1.5 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A49-2 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 8 to 14 V |
| Stop light switch OFF (Brake pedal released) | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG