Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.04
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0722  Output Speed Sensor Circuit No Signal  P077C  Output Speed Sensor Circuit Low  P077D  Output Speed Sensor Circuit High  


DESCRIPTION

The ECM receives a signal from the transmission revolution sensor (NOUT) installed to the continuously variable transaxle and determines the output shaft (secondary pulley) speed in order to control the gear ratio.

The transmission revolution sensor (NOUT) detects the continuously variable transaxle output shaft (secondary pulley) speed and sends a signal to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0722 Output Speed Sensor Circuit No Signal All of the following conditions are met (1 trip detection logic):
·

Vehicle is driven with the shift lever in D

·

Output shaft speed is 300 rpm or more

·

No malfunctions are found in the park/neutral position switch

·

Output shaft speed indicated by the transmission revolution sensor (NOUT) is less than 300 rpm for 2 seconds


·

Wire harness or connector

·

Transmission revolution sensor (NOUT)

·

ECM


Comes on DTC stored
P077C Output Speed Sensor Circuit Low There is no malfunction in transmission revolution sensor (NOUT) signals, and the transmission revolution sensor (NOUT) output voltage is less than 0.2 V for 2 seconds (1 trip detection logic)
·

Wire harness or connector

·

Transmission revolution sensor (NOUT)

·

ECM


Comes on DTC stored
P077D Output Speed Sensor Circuit High There is no malfunction in transmission revolution sensor (NOUT) signals, and the transmission revolution sensor (NOUT) output voltage is higher than 1.8 V for 2 seconds (1 trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NOUT)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM receives a signal from the transmission revolution sensor (NOUT) installed to the continuously variable transaxle and determines the output shaft (secondary pulley) speed in order to control the gear ratio.

If the ECM detects no signal from the transmission revolution sensor (NOUT) even while the vehicle is moving, it will determine that in the transmission revolution sensor (NOUT) is malfunctioning, illuminate the MIL and store a DTC.

WIRING DIAGRAM

C328140E05
0.219,2.865 2.698,3.104 2.479,0.24 10 false Transmission Revolution Sensor (NOUT) 0.219,2.677 0.677,2.875 0.458,0.198 10 false B51 5.938,2.938 6.396,3.135 0.458,0.198 10 false B47 5.927,3.115 6.396,3.323 0.469,0.208 10 false ECM 1.583,1.146 2.042,1.344 0.458,0.198 10 false NOTB 5.656,1.156 6.115,1.354 0.458,0.198 10 false NOTB 1.583,2.125 2.042,2.323 0.458,0.198 10 false NOTO 5.667,2.125 6.125,2.323 0.458,0.198 10 false NOTO 2.073,1.146 2.531,1.344 0.458,0.198 10 false 2 2.083,2.115 2.542,2.313 0.458,0.198 10 false 1 5.375,1.135 5.833,1.333 0.458,0.198 10 false 10 5.458,2.083 5.917,2.281 0.458,0.198 10 false 9 6.271,1.094 6.729,1.292 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (SPD (NOUT) AND NOUT SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NOUT) Secondary pulley speed (NOUT) Min.: 0 rpm
Max.: 12750 rpm
·

0 rpm: Vehicle stopped

·

Approximately 2622 rpm: Vehicle being driven at approximately 60 km/h (37 mph)


Data is displayed in increments of 50 rpm.
NOUT Sensor Voltage Transmission revolution sensor (NOUT) output voltage Min.: 0.000 V
Max.: 4.999 V
0.6 to 1.5 V: Engine idling (Vehicle stopped with shift lever in P or N) -
Powertrain > Engine and ECT > Data List
Tester Display
SPD (NOUT)
NOUT Sensor Voltage
50003 234 402,403

Result:
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)

B

4.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)
a.

Remove the transmission revolution sensor (NOUT).

Click hereDrivetrain>K312 CVT>REVOLUTION SENSOR>REMOVAL


b.

Connect the battery to the transmission revolution sensor (NOUT) as shown in the illustration.

C154686C70
6.073,1.521 6.292,1.927 true 3.521,0.552 3.823,0.552 false 2.427,0.625 2.656,0.625 2.656,0.625 2.729,0.542 false 5.594,1.51 5.396,1.927 true 0.688,0.302 0.927,0.469 0.24,0.167 10 false *a 6.156,1.969 6.615,2.146 0.458,0.177 10 false NOTO 5.208,1.969 5.698,2.135 0.49,0.167 10 false NOTB 2.281,0.552 2.365,0.771 0.083,0.219 10 false 2 3.854,0.49 3.948,0.635 0.094,0.146 10 false 1 0.656,1.333 0.844,1.5 0.188,0.167 10 false *1 2.604,2.083 2.792,2.292 0.188,0.208 10 false *d 4.302,1.417 4.49,1.625 0.188,0.208 10 false *b 5.188,0.552 5.375,0.76 0.188,0.208 10 false *c
*1 Battery - -
*a Ammeter *b Magnet
*c Component without harness connected
(Transmission Revolution Sensor (NOUT))
*d 5 mm or less



c.

Wave a magnetic object left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor (NOUT) to output a high/low signal while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change unless the magnetic object is moved as shown in the illustration.



d.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NOTO) - 2 (NOTB) Low signal 4 to 8 mA
1 (NOTO) - 2 (NOTB) High signal 12 to 16 mA



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NOUT) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NOUT)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NOUT) - ECM)
a.

Disconnect the B51 transmission revolution sensor (NOUT) connector.


b.

Disconnect the B47 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-1 (NOTO) - B47-9 (NOTO) Always Below 1 Ω
B51-2 (NOTB) -B47-10 (NOTB) Always Below 1 Ω
B51-1 (NOTO) or B47-9 (NOTO) - Body ground and other terminals Always 10 kΩ or higher
B51-2 (NOTB) or B47-10 (NOTB) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the B47 ECM connector.


e.

Connect the B51 transmission revolution sensor (NOUT) connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT